Accord of the Month Nominations - June 06

[87accordlxi]

Its time to nominate your favorite ride for AOM: June 06

Check out the Rules & Regulations

All winners in the past year are ineligible for nomination:

June 05 - ICEMAN707
July 05 - BustedBlue
August 05 - Mr Eff
September 05 - thegreatdane
October 05 - 88' Accord Ltd
November 05 - 3GN86LXI
December 05 - Adams86LXI
January 06 - AccordEpicenter
February 06 - Jigga225
March 06 - Hondaman87
April '06 - Legend Master
May 06 - carotman

Members must have 50 posts in order to nominate someone

Duplicate nominations will be deleted

Posts made that are not nominations will be deleted

Invalid nominations will be deleted

There is no need to second a nomination! If a nomination is valid, it will proceed to the voting stage automatically.

[B16KILLA]

I nominate AcidX (aka Cory)... Mods Cosist of:
Tokico HP Struts
Dropzone Springs 2.5'' Drop
16'' Enkei OR-52's
Dunlop SP Sport FM9001'S (205/45/16)
Pilot Fog Lights
Integra Lip
Armrest
Cupholders
Civic Box w/Custom Lid
Custom Short Ram
Crane Cams 11mm Spark Plug Wires
Axle-back 2.5'' Exhuast
Magnaflow Muffler
Also a immaculate interior

[AccordEpicenter]

i nominate WickedAccord because he is my hero

a fantastic 409whp at a mere 12psi, at 17psi, it made giant mid range power. top end dropped off because the injector size are too small. we should've gotten 750cc injectors, but no one expected this amount of power at just 12psi. 486whp could've easily been achieved with 750cc injectors. possibly just a little over 500whp. another problem was due to clutch slippage. again, no one expected these numbers. so a stage3 exedy clutch was opted for. now we have to get an exedy twin plate with flywheel.

-benson's 2.0 resleeved GSR block, fully balanced and blue printed by bensons machine, cp pistons, manley rods, 9:1 compression
-PnP b16 head/multi angle valve job
-ctr cams
-hondata i/m gasket
-str 68mm t/b
-skunk springs/retainers
-hondata s200b p30 ecu
-LSD cable tranny
-full race stage3 GT turbo kit (GT35R)
-custom 3 inch exhaust
-itr cams
-itr manifold
VIDS:
http://keruh.com/3gz/wickedaccord_dyno.mov
http://keruh.com/3gz/wickedaccord_civic.mov
http://keruh.com/3gz/wickedaccord_civic2.mov
http://keruh.com/3gz/wickedaccord_cruisin.mov










ALSO THIS IS A DAILY DRIVER

[gfrg88]

I want to nominate:
88LXi68

Exterior
CF Hood
90-93 Integra Spoiler
Body matched moldings
JDM corners
Se-i alloys (currently)

Interior
90-93 Integra Headrets
84-87 Prelude shift knob and boot
autometer volt and EGT gauge
SE-i center console and SE-I cupholders

Suspension and Brakes
Ground Control Coil Overs
Koni Special Struts (Reds) all around
84-87 Front Upper Prelude Arms
Ingalls Rear Camber Kits
Addco Front and Rear Sway Bars
DC Sport upper strut bar
88TurboAccord rear strut bar
Se-I rear disc conversion
Brembo Cross Drilled and Slotted Front & Rear Rotors
Techna Fit braided lines
Axxis Metal Master Pads

Engine
LS/VTEC Swap
B18A1 Block
Arias 11:1 Pistons
bored .10over
Eagle Rods
new bearings
honed
balanced
clearances checked
Place Racing Mounts
B16A2 Head
CTR Cams
Fererra oversized valves
ITR Valve Springs and Retainers
Port and Polished
3angle valve job
ITR Intake Manifold w/ ITR Throttle Body
JDM 4-1 Itr Exhaust Manifold w/ 2.5" outlet
AEM Fuel Rail
B&M Fuel Pressure Regulator
Short Ram Intake
2.25 Exhaust no cat upgrading to 2.5

Drivetrain
LS Integra S1 tranny
ACT Extreme Pressure Plate
ACT Steet Disc
SCT Streetlite flywheel
Place Racing Axles
Pacesetter 84-87 Prelude Shortthrow shifter

ECU & Electronics
OBD-0 PR3 chipped
Apexi VAFC
MSD SCI-L
MSD Blaster SS Coi
OEM Honda Wires
Place Racing Wire Harness
Removed A/C and P/S

Audio
Alpine 3CD in dash changer
Alpine 6CD in trunk changer
MB Quart 5.25 fronts
Mb Quart 6x9 rears
Zapco Symblink
Zapco 360W Amp

[Legend_master]

mkymonkey.

Engine mods.
90 Civic Hatch altered AEM intake
MSD Blaster Coil
MSD Spark Plug Wires
NGK Irridium Spark Plugs

Suspension
Tokico HP Blues all around
Tokico 1" Drop Springs
riding on 14x6 Enkei Mesh rims

Interior
Restored interior back to LX-i Stock
Tan Arm Rest
SE-i Cup Holders
Ebay Type R Shift Knob (its was only 5 bucks lol)

ICE
ALPINE CDE-3841 (head unit)
ALPINE MRD-M350 (Mono Class D Sub Amp)
JL Audio 300/4 (4 Channel Full Range Amp)
Two 10" JL Audio W3's in a custom box
Infinity 6 1/2" Kappas (front)
Blaupunkt 6x9's (rear)

Soon To Come
SE-i Rear Disk Conversion (already own)
Brembo Slotted rotors all around
EBC Green Stuff break pads
SS Stainless Steel break lines
Pacesetter Headers (for now)
Custom Exhaust piping
Magnaflow muffler

[reanimator420]

Bullard123

1988 Honda accord Lxi


Exterior

Fiberglass Z3 fenders
90-93 integra full body kit
black widow front bumer
spiderman side skirts
spiderman rear
Toyota scion hood scoop (custom)
Jdm sidemarkers
Carbon fiber wiperblades front and rear
custom clear/red tails
H4 headlight housings
custom two tone paint gunmetal / silver
w/gold pinstripe
shaved side mouldings
tinted windows
Drag 17x7 Jdm rims gunmetal w/polished lip
205/40/17 Wanli tires

Interior
Racing black/gray seat covers
painted interior black/gray
carbon fiber floor mats
"H" symbol on dashboard

Engine
A20A3 FI engine
Weaopn R short ram intake
NGK Oem sparkplug wires
Toucan oil air breather
Nippon Denso U groove spark plugs
Koyo High flow radiator (soon to be installed)

Exhaust
Dual exhaust
2 stainless steel dual tip high flow mufflers
2.25 in piping

Suspension
Sprint 2.25 in lowering springs
Tokico struts
Camberkits