- catch can question
- Video from the April 28th Autocross...
- B20A w/ TRANNY 4 SALE
- catch can and oil seperator tank project
- anyone tried these before
- cam swap?
- Any easily modified Cold Air Intakes for the LXi?
- Have you installed a 4th or 6th gen Accord CAI in your 3rd gen? POST HERE!
- Vaccum gauge pod?
- Ticking or tapping sound??
- Any Oval dirt track tips?
- B20A dyno results in!!
- B16A2 Intake manifold
- Have an 86 Lxi FI race car and an 88 Lxi FI parts car, what can I swap for HP gains?
- Who was the guy who drag raced a hatchback and had a h22 in it
- I did it
- modified plenum?
- upper strut tower bar 1986-1989 honda accord
- where are the hard performance numbers?
- Rear Adjustable Upper Control Arms Feeler Post
- going to keep the stock motor. build up advise.
- Light Mod Work
- Performance Chippin
- Questions on HP
- Quarter Wave Resonator to Kill Exhaust Drone
- cam gear hardware question
- Flywheel/pressure plate bolts
- Lower Control Arms are completed :D
- Exhaust woes
- ARP head Studs
- obd1 dizzy's
- A series flywheel bolt pattern matches B series
- High compression? 11.5:1?
- Braaapapapapappapapa!
- cam it
- ignition
- Rebuilding 86 LX-i Hatch
- do i need to remove the center motor mount when removing engine?
- new pace setter headers
- Need ideas
- my 89 lxi
- Intake manifold conversion ?
- Transmission
- replacing all drive belts
- Any information on automatic shift kit????
- Turbo??? A20a1 to a20a3 turbo swap
- Transmission Housing Bolts
- limitations of the transaxle?
- 1988 Honda accord Hatchback Lxi project racer.
- (General) Performance
- OBX header?
- Adjustable Cam gear work around?
- Starting / fuel problem 89 Accord DX
- MSD blaster coil 2
- Shaker scoop on 3rd gen
- Trying to figure out what spolier this is...
- Oil catch can
- Cold Air Intake
- Need help
- A series headers. Help!
- New installation of Web Camshaft
- Can an OBX Exhaust Header for 94-97 fit on an 2 door 88 Honda Accord Dx?
- 5th gear set
- A20A1 performance options
- Wideband in stock o2 location
- Delayed choke and uneven idle
- A20A3 oil pump screen
- Do I need my evap purge solenoid 0bd1
- 86 Iacv swap
- Rack and pinion seal rebuild kit part number
- Alternator with more than 65 A
- A20 rebuild
- Going turbo with carbs possible ?
- Slip joints
- a20 dcoe running
- A20A3 Stroker / Rotating Assembly / What's Possible?!?! Need Help!!!
- Does anyone have actual 272 specs?
- Bee R Limiter
- LS rods
- Need help on A20A3 mods
- Megajolt conversion
- MSD 6AL/Capacitive discharge, what's been done?
- Misfiring
- Rear Lower Control Arm Group Buy Version 2.1, Lighter, Better, No Mods
- Head stud torque spec?
- A20 motor build threads.
- A20 details and B20 rods/pistons thread
- H22 header?? Power adder advice.
- Carburetor Questions for my manual 1987 Accord Hatch
- B16 ITM swap with an Automatic Transmission Question
- whats really needed in the engine bay
- 2-Step button for honda accord 1988 with obd0