PDA

View Full Version : Performance



Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 [18]

  1. catch can question
  2. Video from the April 28th Autocross...
  3. B20A w/ TRANNY 4 SALE
  4. catch can and oil seperator tank project
  5. anyone tried these before
  6. cam swap?
  7. Any easily modified Cold Air Intakes for the LXi?
  8. Have you installed a 4th or 6th gen Accord CAI in your 3rd gen? POST HERE!
  9. Vaccum gauge pod?
  10. Ticking or tapping sound??
  11. Any Oval dirt track tips?
  12. B20A dyno results in!!
  13. B16A2 Intake manifold
  14. Have an 86 Lxi FI race car and an 88 Lxi FI parts car, what can I swap for HP gains?
  15. Who was the guy who drag raced a hatchback and had a h22 in it
  16. I did it
  17. modified plenum?
  18. upper strut tower bar 1986-1989 honda accord
  19. where are the hard performance numbers?
  20. Rear Adjustable Upper Control Arms Feeler Post
  21. going to keep the stock motor. build up advise.
  22. Light Mod Work
  23. Performance Chippin
  24. Questions on HP
  25. Quarter Wave Resonator to Kill Exhaust Drone
  26. cam gear hardware question
  27. Flywheel/pressure plate bolts
  28. Lower Control Arms are completed :D
  29. Exhaust woes
  30. ARP head Studs
  31. obd1 dizzy's
  32. A series flywheel bolt pattern matches B series
  33. High compression? 11.5:1?
  34. Braaapapapapappapapa!
  35. cam it
  36. ignition
  37. Rebuilding 86 LX-i Hatch
  38. do i need to remove the center motor mount when removing engine?
  39. new pace setter headers
  40. Need ideas
  41. my 89 lxi
  42. Intake manifold conversion ?
  43. Transmission
  44. replacing all drive belts
  45. Any information on automatic shift kit????
  46. Turbo??? A20a1 to a20a3 turbo swap
  47. Transmission Housing Bolts
  48. limitations of the transaxle?
  49. 1988 Honda accord Hatchback Lxi project racer.
  50. (General) Performance
  51. OBX header?
  52. Adjustable Cam gear work around?
  53. Starting / fuel problem 89 Accord DX
  54. MSD blaster coil 2
  55. Shaker scoop on 3rd gen
  56. Trying to figure out what spolier this is...
  57. Oil catch can
  58. Cold Air Intake
  59. Need help
  60. A series headers. Help!
  61. New installation of Web Camshaft
  62. Can an OBX Exhaust Header for 94-97 fit on an 2 door 88 Honda Accord Dx?
  63. 5th gear set
  64. A20A1 performance options
  65. Wideband in stock o2 location
  66. Delayed choke and uneven idle
  67. A20A3 oil pump screen
  68. Do I need my evap purge solenoid 0bd1
  69. 86 Iacv swap
  70. Rack and pinion seal rebuild kit part number
  71. Alternator with more than 65 A
  72. A20 rebuild
  73. Going turbo with carbs possible ?
  74. Slip joints
  75. a20 dcoe running
  76. A20A3 Stroker / Rotating Assembly / What's Possible?!?! Need Help!!!
  77. Does anyone have actual 272 specs?
  78. Bee R Limiter
  79. LS rods
  80. Need help on A20A3 mods
  81. Megajolt conversion
  82. MSD 6AL/Capacitive discharge, what's been done?
  83. Misfiring
  84. Rear Lower Control Arm Group Buy Version 2.1, Lighter, Better, No Mods
  85. Head stud torque spec?
  86. A20 motor build threads.
  87. A20 details and B20 rods/pistons thread
  88. H22 header?? Power adder advice.
  89. Carburetor Questions for my manual 1987 Accord Hatch
  90. B16 ITM swap with an Automatic Transmission Question
  91. whats really needed in the engine bay
  92. 2-Step button for honda accord 1988 with obd0