B2oa Is Allmost In

[BOLINKXR-89LXI]

I should be ready to put it in in 2 weeks I no its going to be a lot of fun:eek:
http://www.3geez.kicks-ass.net/t/B20A3.jpg http://www.3geez.kicks-ass.net/t/B20A4.jpg http://www.3geez.kicks-ass.net/t/B20A5.jpg

:smokin:

[BOLINKXR-89LXI]

THE DC HEADER I BOT WAS FOR A 89 PRALUDE I GOT THE Y PIPE FIXED THIS WEEK SO IT FITS ON THE ENGINE
http://www.3geez.kicks-ass.net/t/dc1.jpg http://www.3geez.kicks-ass.net/t/dc2.jpg

:smokin:

[carotman]

It looks real good!!!!

Looks like I'll need to mod mine too.

Where did you buy the DC header?

[BOLINKXR-89LXI]

http://www.3geez.kicks-ass.net/t/B20A2.JGP http://www.3geez.kicks-ass.net/t/B20A3.JGP

[BOLINKXR-89LXI]

YA DC ALL THE WAY

http://www.3geez.kicks-ass.net/t/dc4.jgp

[BOLINKXR-89LXI]

:) i made a new axel for my be 20a

when i got my engine it had the shaft with the carrier bearing so I needed to make a new shaft to replace the long one on the left side I got licky and found out you can use a right side axel and join them together and its the rite length . http://www.3geez.kicks-ass.net/t/b20aaxel.jpg :)

[PhydeauX]

They don't call them equal length axles for nothinging ;)

andy

[RobT5580]

So your saying your using the regular A20A right axle?

[RCracer]

Looking good.
I measured the original B20a axels (driveshafts) from my parts car and they were both the same as the shorter driveshaft from the A20a so that will work fine.

[carotman]

sweet :) I got a spare axle here :)

I'm glad I'll be able to use it.

[iloveJDMblackrims69]

what can i say.......IM JEALOUS!!!!

[socal3rdgen]

im going to ask a question for bolink. he got a prelude speedometer today for his b20. does this work correctly with the b20. his didnt come with one. and did anyone hookup there A/C to there b20. is so was it hard or did you have to fabricate something for it.

[YK86]

Speedometer as in the part that goes into the tranny? If so, you can use the one from the A20. If you meant the actual speedo, I'm not sure. The A/C pump is different and the bracket is as well.

[socal3rdgen]

yeah thats it yasu the part that goes into the tranny. :lol bolinkwent and bought one while i was sanding my gay ass paint away. I told him last night he should ask the board before he goes buyin shit. :lol and about the pump has anyone put A/C on there b20. cuz its hot as hell out here about 9 months out of the year. were in our cold season of the mid 70's brrrrrrrrr.........:flip:

[RCracer]

I used the speed sensor out of the original B20a tranny & it worked fine with the A20 speedo until I swaped in the one from the B20a. Only cos it has a higher top speed and no auto gear selector between the fuel/temp gauges.
I have a A/C compressor and all the associated pullys etc from a B20a (but its hella heavy).

[RobT5580]

For the A/C you should be able to get away with modifing or making a new bracket and then finding the right size belt. This should work fine using the A20 a/c compressor becuse the car has the A20 lines still so you wont have to mess with any of that unless the position is way off from the old one.

[carotman]

Where are the O2 sensor holes on the header?

[socal3rdgen]

there right by where the header goes from 4 to 2. near the flange going to 2. you can see a bit of it on the second pics above, there are there i seen them up close.

[BOLINKXR-89LXI]

thanks socal for your help Iv been working alot

Im surprised no one has made something for there ac yet I gess I will be the first I dont think I can get a good look at it intill the a20a is out I dont think I can get thru the summer with out it I do lot of driven to get to work.

I got my new b20a timeing belt today If anyone needs the part # here it is .

http://www.3geez.kicks-ass.net/t/b20abelt.jpg

Me and socal been doing a lot of work on strippen his car for a new paint job its comeing along little by little

http://www.3geez.kicks-ass.net/t/joel1.jpg :smokin:

[BOLINKXR-89LXI]

here you go carotman Im trying to make my car smog legal my b20a came with egr:) :smokin:
http://www.3geez.kicks-ass.net/t/dc5.jpg

[socal3rdgen]

Originally posted by BOLINKXR-89LXI
thanks socal for your help Iv been working alot

Im surprised no one has made something for there ac yet I gess I will be the first I dont think I can get a good look at it intill the a20a is out I dont think I can get thru the summer with out it I do lot of driven to get to work.

I got my new b20a timeing belt today If anyone needs the part # here it is .

http://www.3geez.kicks-ass.net/t/b20abelt.jpg

Me and socal been doing a lot of work on strippen his car for a new paint job its comeing along little by little

http://www.3geez.kicks-ass.net/t/joel1.jpg :smokin:

ha ha yeah. thats how it looks right now. letme tell you guys somethin. PLEASE BY ALL MEANS PLEASE DO NOT USE AIRCRAFT STRIPPER IN A CAN, USE THE AIRCRAFT STRIPPER IN THE GALLON. it works so much better. we were sittin there watching the stipper eat at the paint. :lol yeah i know after 2 long days anything is funny.