PDA

View Full Version : coolent port help



KBs playtoy
02-23-2005, 12:05 PM
well i finially found me another motor, but had to swap my intake and exhaust mani's over to the new motor. but apon starting i noticed that i had a port on the front left side of the intake mani and i though it was a vaccum port but once it got warm enough it started pouring out coolant so i have no freaking clue where the tubing is (( it would make it easier to find the other port if i knew where it was)) but can any oh you all tell me what it is and possibly where it might need to hook up to.

KBs playtoy
02-23-2005, 12:09 PM
i have a pic but it wont let me post it up so if one of you all would like to post it for me........

A20A1
02-23-2005, 05:00 PM
What motor is it? Carb or EFI? that makes a big difference... coolant / vaccum port means nothing if you don't tells us what you have.

KBs playtoy
02-23-2005, 07:42 PM
89 fi lxi

A20A1
02-23-2005, 08:12 PM
you hooked up the coolant lines that ran under the intake manifold right?

danronian
02-23-2005, 08:23 PM
There is at least two coolant lines around the TB area but I can't really explain them w/o a picture. Look in the FREE ONLINE Honda Repair Manual, it should show you the coolant lines. If not, check on Majestic HOnda's online catalogue, I am sure that also has diagrams of the coolant system and parts numbers of each hose if you want pre-formed ones, which aren't neccessary unless you have the $$.

KBs playtoy
02-24-2005, 08:35 AM
every pic in any manual that i look at it shows it from the throttle body side. and the port is on the side with all the vaccum and fuel return line are on. so i have no freaking clue. worked on it a bit last night. it's running like shit. i dont know. i think i'm gonna just block the damn thing off...

Vinny
02-24-2005, 08:48 AM
Bare with me, the accords at home today so I am going off memory...........


Infront of the intake manifold just to the right of the TB as you face the engine bay is where the IAC Valve (Idle Air Control), I believe thats what it is. It should have 2 coolant lines going to it. The one on the left side as you face the car goes somewhere around the TB and the one on the right (drivers side) around the intake and under to the first fitting on the coolant pipe inder the intake. Its a bit of a pain to get to but it can be done.

If its comming from 13 in the pic its the IAC

http://www.hondaautomotiveparts.com/catimgs/13SG70_D06.gif

If I am right then the part you need is hose you want is PN 19518-PH3-000 and clamps are PN 95002-41250-04

http://www.hondaautomotiveparts.com/catimgs/13SG70_E0301.gif

KBs playtoy
02-24-2005, 12:03 PM
can some one send me an email address so i can send you the pic and load it on the website. cause it wont let me

KBs playtoy
02-24-2005, 12:06 PM
the port os on the drivers side of the intake manifold. like three inches back from the fuel return line that goes back to the fire wall......

Vinny
02-24-2005, 12:10 PM
email it to me...............

[email protected]

KBs playtoy
02-25-2005, 11:18 AM
vinny i sent them to ya last night before i left to go to work.

Vinny
02-25-2005, 11:22 AM
I just got them. Let me see if I can upload them for you. Only thing I can think of in that area is the drivers side port for the IAC Valve

KBs playtoy
02-25-2005, 11:29 AM
if ya can't figure it out just post on the forum and we'll c whathappens then. cause i'm about fed up with this car so badly...

Vinny
02-25-2005, 11:42 AM
its the IAC/ Look at the 2 pics I posted earlier. Its the Drivers side of part number 8 in the top pic. The hose that goes to it is pat number 24 in the second picture. It goes from the IAC, then loops under the intake and goes to the coolant pipe behind the block


http://3geez.com/attachment.php?attachmentid=4062

http://3geez.com/attachment.php?attachmentid=4063

danronian
02-25-2005, 11:55 AM
That hose has a real sharp bend and without buying the pre-molded hose from Honda you probably won't be able to make it out of the universal hose without it kinking. I came to this conclusion and this hose remains original on my engine after 174 mi. The thing is real hard and leaks a bit at the end above the oil filter so i'd best replace it real soon.

POS carb
02-25-2005, 03:27 PM
it's for the fast idle I think, it should also be leaking where it runs back to, find it and runa hose to it

KBs playtoy
02-27-2005, 07:36 PM
well i took my two stage intake and my 4-2-1 mani off my old motor and put it on this other motor i got from salvage cause it only had the one stage intake and the 4-1 mani. so i have ports on the intake that i had to plug off cause i had no where to hook them up to the water pipe..