Winter Project *Lots of pics*

[Gemini2003]

I actually had one but it got stolen out of my shop :-( I have suspicions as always but no proof *sigh* So I am using this cheesy Weapon R filter and a piece of aluminum that I had in my shop... I will be buying a new cold air intake and will be routing it down thru where the battery is now. The battery will be relocated to the trunk in the near future.

I checked the main relay, replaced it and now I have power to the pump and ECU when I turn on the car, ECU is now flashing 13 red flashes indicating: BARO Sensor (Atmospheric Pressure) defective circuit or unplugged / defective sensor. It's missing lol (as this happens to little sensors over a year). I looked in the Hanes manual and it's supposed to be in the trunk... the thing is I looked in the trunk and couldn't find it in my working accord... but I'm not surprised it's a different model. I will be going to the junk yard first thing in the morning.

*Edit - I just looked in the online manual (http://www.pauldesign.ru/honda/shopmanual.html) it says it's behind the glovebox... I'll take look tomorrow*

On that note if anyone knows if it's not in the trunk please let me know.

All in all the mistakes I've had to fix are due to inexperience and next time I will be sure to do things a little differently to avoid this same issue.


Justin86, Your rear strut tower brace didn't work quite right... I made it fit, We will see if it effects my alignment... (no offense or anything I know things aren't always perfect)

http://geminiwebhosting.ca/images2/DSCI0003cs.JPG

[Bass Man]

Looking good! But, why is the picture on top flipped left to right?

To confuse the HELL out of me!! I spent like 3 minutes looking at it trying to figure out how the header was in front and the tranny was on the right!!

[carotman]

http://carotman.no-ip.com:8888/personal_site/howto/eficonversion/images/pressuresensor.jpg

The sensor is bolted to the heater blower.

[Gemini2003]

THANKS CAROTMAN!

After fixing a small fuel issue i got it STARTED!

Video a little later. (it's a short one)

WHOO HOO

[Hash_man_Se_i]

Awesome! congrats... must feel really good!. Can;t wait to see the video.

[redaztec]

Glad to hear it's running!

[Gemini2003]

OK Sorry about the audio, Bad camera and open down pipe don't mix.....

BUT...

Here's the Video :-) (http://www.jumpcut.com/view?id=577883CA080011DD8316000423CEF5B0)

I'll get a better video with my buddies digital video recorder later :-)

[A18A]

i bet that felt good when you started it :D

[87roach]

That is just AWESOME man!! Finally got the car going, I'd say the hardest part is done, now you just gotta get the rest installed. Can't wait to stop by! Keep up the good work.

[forrest89sei]

w000t Congrats man! She runs!

Looking forward to the finished project

[A18A]

you should drive it how it is :)

[Gemini2003]

I want to, but I need to take care of like 5 things before I can tho!

[MessyHonda]

man i wish i had a rebuilt engine

[bullard123]

She sounds good man!

[Gemini2003]

Hey guys! A little update... I'm doing all the small things now to make it road worthy... I got the last few odds and ends today and i only have a few things left to do... no pictures as it's very boring stuff lol work has been eating up all my time :-( But it's gunna be worth it... Thanks again for stoppin by

[Vector]

was wonderin if you were still around workin on that guy, good work... lookin forward to seeing it finished... going to have to have a mini meet once mine, yours, 87roach are done.

[87roach]

Heck yea man, although "done" might not be the right word haha. Looking forward to a meet and checking everyones cars out, get some work done mike! :P

[Gemini2003]

life is stupid busy right now..... I will be working on it again soon tune it up sometime this week

[Gemini2003]

Sorry for the no updates BUT...

I finally re-installed my gastank today... it was interesting running my new brake lines..i did get them up out of the way anyway. I'm getting the windshield re-installed tomorrow and then all that's left (to get it rolling) is the drivers seat and shiftlinkange :-)

I am taking all the orange panels from my other car and putting them on this one until i get all the body work done.... it's cheating but i don't care at this poitn i just want it on the road. I may have it insured next weekend :-)

[Civic Accord Honda]

=d

[A18A]

I am taking all the orange panels from my other car and putting them on this one until i get all the body work done.... it's cheating but i don't care at this poitn i just want it on the road. I may have it insured next weekend :-)

haha i know how you feel there. good luck

[Gemini2003]

YES!! My Windshield is installed, pretty easy to do, I"ll be doing it myself next time :-P

I have like two major things left... Shift linkage and driver seat and then

TEST DRIVE!

[Gemini2003]

IT LIVES! WHOO HOO!!

I only moved about 30 ft BUT i did it! The car moved! WHOO HOO

[bobafett]

congratulations! i'm jealous mine hasn't moved in about 1.5 years so I am ready to share the feeling of my accord moving under its own power.

[A18A]

yay!!, you should get us some new pics :)

[Civic Accord Honda]

yay!!, you should get us some new pics :)

[Gemini2003]

Picture update:

Rims on, whole front clip swapped over, trunk and rear bumper aswell.

http://geminiwebhosting.ca/images2/DSCI0075s.jpg
http://geminiwebhosting.ca/images2/DSCI0078s.jpg
http://geminiwebhosting.ca/images2/DSCI0077s.jpg
http://geminiwebhosting.ca/images2/DSCI0079s.jpg

Front strut tower brace on:

http://geminiwebhosting.ca/images2/DSCI0086s.jpg


That was yesterday and this is today:

http://geminiwebhosting.ca/images2/DSCI0088s.jpg
http://geminiwebhosting.ca/images2/DSCI0089s.jpg
http://geminiwebhosting.ca/images2/DSCI0090s.jpg
http://geminiwebhosting.ca/images2/DSCI0091s.jpg

inside shot:
http://geminiwebhosting.ca/images2/DSCI0080s.jpg


So yeah there it is.... I'll be throwing insurence on it as soon as I can :-P

[EricW]

Looks like its coming right along. Keep up the good work.

[Cheeseburger]

nice update!

[MessyHonda]

really looks good. now that we have pics i want a video..haha

[bullard123]

She's coming back together nicely! Seems like the front of the car is way higher than the back. Could be because you are parked on a hill though. Its good to see the end of this project:) Mine is almost over also

[Civic Accord Honda]

w00t :)

[87roach]

Looking good man, its comming along well. hope we get out for a drive soon :D

[A18A]

yeah she looks good, nice to see her complete again, well not complete, but driveable :D

[Gemini2003]

Hey all :-)

Wow if I didn't know about all the work I've done to this car I'd say it drives like a piece of crap! lol BUT knowing all that I've done the car feels pretty good...

I say that because I'm mainly getting used to the ROCK HARD suspension, if I run over a pebble it sounds like i just curbbed my car! This is due to: Integra Shocks and Springs as well as my front and rear strut bars, and the tie rod set. (picture below)

http://img141.imageshack.us/img141/6411/sbarsuo5.jpg

I've got some electrical issues to work out... My taillights don't work and I've got a grounding issue to work out... this is the little stuff I hate because It feels so tedious.

As for the performance.... I've got about 120 KM on the block now and WOW It's quick! I haven't even stepped on the pedal yet... My car feels like it has V-Tec man... I've got the custom cam from Colt cams and as soon as I hit 3100 RPM it wants to pull and pull... and hard too... which is a tease of course as I can't really get the rpm too high for another 4850 KM lol

Unfortunately my car is not where I want it to be... It only has the Driver seat installed... the Re-upholstering job I did sucks ass so I need to do it again...but this time I've got more experience on my side (the roof looks good still but my A,B and C pillars are falling apart :-( )

I don't have money for new carpet right now so my interior is going to look like crap for a while :-(

All in all it's OK... Not Good but OK. It's going to be alot nicer in the near future when I get some more time and money to put into it.

[84Accord]

Guess What? I FINALLY got my steering wheel that's been on back order and back order...

But now.....
http://www.gemini-online.net/web/images/DSC01037s.jpg
All the way from Italy ladies and gents...


http://www.gemini-online.net/web/images/DSC01039s.jpg

:rockon: :thumbup: :bow: MOMO Jet Steering wheel. SEXY. :rockon: :flip: :cheers:

That was the icing on the cake of an INCREDIBLE day for me :-).

i bought the exact same steering wheel for 215

[bullard123]

Hey all :-)

Wow if I didn't know about all the work I've done to this car I'd say it drives like a piece of crap! lol BUT knowing all that I've done the car feels pretty good...

I say that because I'm mainly getting used to the ROCK HARD suspension, if I run over a pebble it sounds like i just curbbed my car! This is due to: Integra Shocks and Springs as well as my front and rear strut bars, and the tie rod set. (picture below)

http://img141.imageshack.us/img141/6411/sbarsuo5.jpg

I've got some electrical issues to work out... My taillights don't work and I've got a grounding issue to work out... this is the little stuff I hate because It feels so tedious.

As for the performance.... I've got about 120 KM on the block now and WOW It's quick! I haven't even stepped on the pedal yet... My car feels like it has V-Tec man... I've got the custom cam from Colt cams and as soon as I hit 3100 RPM it wants to pull and pull... and hard too... which is a tease of course as I can't really get the rpm too high for another 4850 KM lol

Unfortunately my car is not where I want it to be... It only has the Driver seat installed... the Re-upholstering job I did sucks ass so I need to do it again...but this time I've got more experience on my side (the roof looks good still but my A,B and C pillars are falling apart :-( )

I don't have money for new carpet right now so my interior is going to look like crap for a while :-(

All in all it's OK... Not Good but OK. It's going to be alot nicer in the near future when I get some more time and money to put into it.
Yes I can realte to the budget thing myself. The hard part is over now. Now its time to relax and take your time

[MessyHonda]

i bought the exact same steering wheel for 215



what kind of hub are you running? would it work on a 3gee...i want an aftermarket wheel also. and that momo looks like sex

[84Accord]

what kind of hub are you running? would it work on a 3gee...i want an aftermarket wheel also. and that momo looks like sex

so use this hub: http://www.modacar.com/products/Honda/Accord/ZMHUBA/MOMO+Hub+Adaptor.html

and this steering wheel
http://www.modacar.com/products/Honda/Accord/MMJSW/Momo+Jet+Steering+Wheels.html

along with those im running an NRG short quick release. it is about the same distance total with hub quick release and wheel from the wiper and turn signals as the stock wheel was.

id order it from them. great customer service and fairly quick on getting the parts. and they are cheaper than most places

[thegreatdane]

Wow back together at last!! Yay!

Did you get a new oem honda windshield or a replacement one?

[1ajs]

man that looks good you going to take the LX badge off? for painting?

[A18A]

looks bloody awesome

[Gemini2003]

N/t

[Gemini2003]

N/t

[A18A]

?

[Civic Accord Honda]

??

[Gemini2003]

(no txt) I deleted my posts.

[Civic Accord Honda]

why did u delete them??

[Gemini2003]

Started a new thead for the topic. HHO Gas Hybrid Accord (http://3geez.com/forum/showthread.php?p=892050#post892050)


I'll get an update this weekend I promise... with pictures and stuff lol

[AccordB20A]

pics of what u done kthx

[Civic Accord Honda]

bump
http://www.youtube.com/watch?v=37obz2G7uas

[Gemini2003]

I'm SORRY!

Life's busy what can I say?

A few updates:

Replaced my Headlights:

Before:
http://geminiwebhosting.ca/images2/DSCI0106s.JPG

After:
http://geminiwebhosting.ca/images2/DSCI0108s.JPG


Properly installed my guage cluster.. had some extra sound dampening so I figured it wouldn't hurt:

http://geminiwebhosting.ca/images2/DSCI0111s.JPG

Gauge cover:

http://geminiwebhosting.ca/images2/DSCI0112s.JPG


I cut down the Gauge cover... I found it to be too big, I'll be doing a fiberglass edge on this to make it look cleaner:

http://geminiwebhosting.ca/images2/DSCI0113s.JPG

I messed up while cutting this with a saw, The right side is stright but the left side has a curve in it... I'll be fixing this:

http://geminiwebhosting.ca/images2/DSCI01132s.JPG


I was playing around with a 4G spoiler, what do you think?:

http://geminiwebhosting.ca/images2/DSCI0100s.JPG
http://geminiwebhosting.ca/images2/DSCI0102s.JPG
http://geminiwebhosting.ca/images2/DSCI0103s.JPG


OH, and I installed my prelude seats :-)

http://geminiwebhosting.ca/images2/DSCI0104s.JPG

[MessyHonda]

nice update

[EricW]

Looking good. Not sure about the gauge cluster thing but I guess I'll have to wait till your done to see the end result.

[Timaculent]

awesome job man

[2oodoor]

4 g spoiler looks fine !

[Hauntd ca3]

looking good guv
thats the same spoiler that i've got

[Civic Accord Honda]

looks great !! and i believe the 4g and 3g wings are the same i know on ebay it says 86-93 on them and yes it looks great (Y)

[A18A]

im interested in seeing the gauges finished

[Gemini2003]

I'm Moving! This is Good news as now I'll have space to work on my car again!

More updates to come :-)

[Civic Accord Honda]

sweet!

[1ajs]

updates?

:sadwave::stick:

['A20A3']

update fail.

[AccordB20A]

indeed someone hasnt been online for ages!

[MessyHonda]

yeah he has a cool project...hope he is not locked up

[Gemini2003]

lol holy crap, yeah I know major update fail.

Truth is that it's sitting in the back yard.... No excuses,

I will update when there is somthing to update.... got a few weeks off Starting June 13th...

Thanks for the support guys

[MessyHonda]

nice to see you

[Hazwan]

Can't wait to see more updates!

[speedpenguin]

I'll mark my calendar lol

[Connor_LX-i]

This is an awesome project, let's get some more work done on it!

[carotman]

I know how it is. You see the car everyday but find lame excuses not to start working on it cause you know it's going to take all your spare time for the next month :D

[Gemini2003]

I'm still alive.... So is the car... It's running and it's still in the back yard.... I'm thinking of putting all my cool stereo stuff in my New Dodge Stealth and using this car for auto cross now! Updates coming. Hopefully sooner then later.... Geez this winter project is now like a 5 year project!

[87roach]

Good to see you are still around.

[Civic Accord Honda]

glad to see your still around :)
confused on why you would rather drive a dodge then a 3g tho =/

[2oodoor]

glad to see your still around :)
confused on why you would rather drive a dodge then a 3g tho =/
Stealth...
it's a Mitsubitchi 3000 with a corncob pipe n cowboy hat... lol
http://img.photobucket.com/albums/v390/jerggy13/586ac536.jpg

[Gemini2003]

That last post was a horrible stealth! I think it was supposed to be lol

This is mine:
http://members.shaw.ca/michael4/st1.jpg
http://members.shaw.ca/michael4/st2.jpg

:-)

[A18A]

this car was the very first build thread ive seen and followed lol

[Gemini2003]

There is you and a few other awesome members that have been following my thread and I would like to send out a very special thank you for that!!!

I hope I Don't let you all down, this summer is going to be a good one!!

[A18A]

well ill be sticking around for the weeks/months/years to come to see the finished result :D

[MessyHonda]

wow man...i remember when this thead was a baby....good to see you are still around...i hope you got your drivers licence back

[2drSE-i]

wow man...i remember when this thead was a baby....good to see you are still around...i hope you got your drivers licence back

Me too.... i was 18 at the time my god....

[Gemini2003]

Update: I blew up the tranny in my Stealth lol so i'm driving my Accord again :-) I've removed the head liner that I re-upholstered as the glue sucked and it all fell off!

So basically I have no interior etc etc but i'm on the road and it's fun to drive it again (9it's a little loud tho)

More updates soon :-)

[1ajs]

Update: I blew up the tranny in my Stealth lol so i'm driving my Accord again :-) I've removed the head liner that I re-upholstered as the glue sucked and it all fell off!

So basically I have no interior etc etc but i'm on the road and it's fun to drive it again (9it's a little loud tho)

More updates soon :-)
3geezus strikes again lol

looks forward to an update:rockon:

[1ajs]

so?

[SettleMoore]

Am I the only one that can't see any of the pictures he posted except stealth?

[Tomisimo]

o_O this was a long time ago.. I remember this. :rolleyes:

and no, he deleted hes pics from photobucket it seems.. bad move.. thats why I have it sorted to a 3Geez sub album in mine.

[SettleMoore]

But I wanna see ;_;

[Gemini2003]

Hello Everyone

I hate to sound like a broken record but....

The project is still in "project status" but as everyone know life comes first.

Good news is I have a line on a paint booth so painting my car is going to be cheap.

As for all my pictures not working I deleted one of my domain's forgetting that EVERYONE OF MY PICTURES was on it.

I am working to restore all my images.

Thank you all who have been following my thread for years You all ROCK MY WORLD. THanks.

[forrest89sei]

Hello Everyone

I hate to sound like a broken record but....

The project is still in "project status" but as everyone know life comes first.

Good news is I have a line on a paint booth so painting my car is going to be cheap.

As for all my pictures not working I deleted one of my domain's forgetting that EVERYONE OF MY PICTURES was on it.

I am working to restore all my images.

Thank you all who have been following my thread for years You all ROCK MY WORLD. THanks.

Yay nice to have a update, Looking forward to pics

[Gemini2003]

***WHEW***

That took FOREVER.

I have fixed every broken image I could! (35 pages worth!!!) Now any of the new guys can see my project in all it's glory!

and by that right now it's sitting in my parents backyard waiting to be worked on!

[MessyHonda]

i think i said it and i will say it again i remember when your thread was only around 6-7 pages

[A18A]

i was having a complain to someone very recently that the pics in this thread weren't working lol. good to see them back :)

[Gemini2003]

lol yeah, got rid of my domain, needed to move all the pictures over and edit every post i've made.

and Messy: i think i said it and i will say it again i will be working on her again one day! hopefully soon!

Has any progress been made on nice fitting lips or kits?

[87roach]

Holy old thread.

Good job on getting the pictures back up.

[Gemini2003]

I'm Back !! Sept 1st I get a shop again!!!

It's been almost 4 years to the month ( I just checked my updates ) since i lost my shop and stopped working on my baby.

I hope to not disappoint once again! Anyone want a Dodge Stealth? lol

[Gemini2003]

Has any progress been made on nice fitting lips or kits?

[A18A]

I clicked on this thread fearing a "I sold my car" post lol. Good to see you're gonna get stuck back into it :thumbup:

[Gemini2003]

Hell no! i've hauled my baby everywhere, I am absolutely getting back into it!

[Gemini2003]

I'm itching to get started again.. todays's task? Kill 6-10 hornet hives/nests to access all my tools lol

[A18A]

have fun :thumbup:

[Civic Accord Honda]

holy heck! glad to see you still have the car! i remember reading this back when i first joined!

[Gemini2003]

My mind has been racing... So many idea's Anyone making LED taillights yet ?

[Gemini2003]

I'm Moved in! Bring on the projects!

[Civic Accord Honda]

pics!

[Gemini2003]

Shop is almost ready!

I wanna do some little things first see!

http://imageshack.us/a/img443/897/imag1892s.jpg
http://imageshack.us/a/img11/2272/imag1893s.jpg
http://imageshack.us/a/img201/8309/imag1889s.jpg

[MessyHonda]

nice to see a new place so you can work on the car

[Gemini2003]

We're closer! Car is on my property again!! Now to get rid of another project or two!! You all rock!

[Gemini2003]

The Reason I've not been able to work on baby....

5257

Too many Damn Cars and trucks!!!!

[Gemini2003]

....and then my house floods. FACK.

[Dr_Snooz]

Oh dear. What's going on? Are you okay?

[Gemini2003]

HAHA Yeah I'M ok, lol my place not so much......



My bathroom faucet broke and I came home a short 8 hours later.


I'm now looking for accommodation for the next 3 months.


WHOOOOO .... Honest I get SO CLOSE to working on her again and stuff happens.... SHE WILL NOT BE FORGOTTEN.

[Gemini2003]

http://geminiwebhosting.ca/20131101_133521_resized2.jpg

:-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-) :-)

[Dr_Snooz]

Yay!

[Gemini2003]

So Happy!!! I just cleaned 3 years of gunk from all of her crooks and crannies.... A few spiders.... more then a few beer caps hahaha


man.... I really forgot all the hours I have put into this car.....


I've done so much so far!

[2drSE-i]

8 years is a long winter sir. Glad to see you back at it!

[Hash_man_Se_i]

Glad to see it get some attention again

[Gemini2003]

.... I keep finding things to clean and sort grrr but i can see the light :-)

First thing on the agenda is make the car road legal again of course... I stopped driving it because I failed to yield and a cop pulled me over. Gave me a warning but made up for it by also giving me a Box 1 inspection. I found a list of requirements online and have to check off one by one.

Can anyone from BC verify this is the right inspection?

http://www.th.gov.bc.ca/CVSE/vehicle_inspections/PDF/MV3199.pdf


I know I will need to replace my windshield... not a fun job in the cold of pick-n-pull however it's a quick $300 in savings grabbing a windshield from the wrecker and doing it yourself.

Bonus: I found two rolls of windshield removal wire when cleaning up my tons of crap :-)

[Hash_man_Se_i]

.... I keep finding things to clean and sort grrr but i can see the light :-)

First thing on the agenda is make the car road legal again of course... I stopped driving it because I failed to yield and a cop pulled me over. Gave me a warning but made up for it by also giving me a Box 1 inspection. I found a list of requirements online and have to check off one by one.

Can anyone from BC verify this is the right inspection?

http://www.th.gov.bc.ca/CVSE/vehicle_inspections/PDF/MV3199.pdf


I know I will need to replace my windshield... not a fun job in the cold of pick-n-pull however it's a quick $300 in savings grabbing a windshield from the wrecker and doing it yourself.

Bonus: I found two rolls of windshield removal wire when cleaning up my tons of crap :-)

That looks like the inspection I had to have done for OOP in BC. Is it really $300 out there to have a windshield put in? that's crazy expensive.

[Gemini2003]

Well.. the wind shield itself is going to be a couple hundred bucks plus the install...

[Dr_Snooz]

Don't you have one of those businesses that sits right next to the wrecking yard? When you go for a windshield, they run into the yard to grab it. I've gotten windshields for super cheap that way.

[Gemini2003]

I'm definitely going to the year to grab one I called the glass shop today and they said 500 bucks.



So I just saftied my car myself:

http://geminiwebhosting.ca/images2/20131107_183302_resized_11000pix.jpg

I found a piece of fiberglass and got inspired while I Was fixing one of my doors...

I really really want to make fiberglass door panels... Not too hard hey?



http://geminiwebhosting.ca/images2/fiberglass.jpg
of course this was a quick mock up too see how I could hang it from the top of the door frame but I think I could do something that would be really neat :-)

[Gemini2003]

Had a good day :-)

Driver seat installed :-)

More mock up for the door panel done :-)

http://geminiwebhosting.ca/images2/mock1.jpg

http://geminiwebhosting.ca/images2/mock2.jpg

Awesome find for $20 at the junkyard

http://geminiwebhosting.ca/images2/rim resized.jpg

20" 5 bolt Aluminum rim

[dieselgus]

Methinks you will have a hard time with that inspection sheet when you hand it over to the ICBC agent. Assuming this is an out of province, pre registration inspection, you will need to take it to somewhere like Canadian Tire, fork over $120 (or whatever it is now) and have them go through it. If it is an already registered vehicle and the officer is sending you in for a VI, my guess is the officer feels your car is an unsafe vehicle. Get it fixed and inspected properly.

Last windshield I changed was $100 (depends on how you have your insurance set up. In Manitoba I paid zero dollars for windshields).

[Gemini2003]

Haha no no I wasn't trying to pass it myself i wanted to know what I needed to fix before bringing it in lol

Got some much needed TLC done today

http://geminiwebhosting.ca/images2/20131111_123230_resized_1.jpg



http://geminiwebhosting.ca/images2/20131111_142924_resized_1.jpg

[Gemini2003]

Windshield re-installed :-)

Next up: get horn and heater working

[Hash_man_Se_i]

Good to see more progress being made, I always really liked that orange colour... BC inspections do suck, when I had to get my Accord inspected for out of province I ended up having to go to a buddies hook up for it as it wouldn't pass by most shops standards... So stupid though. If only you were in Van I would tell you where to go for inspection.

[derolph]

Windshield re-installed :-)

Next up: get horn and heater workingI just replaced the horns in my 88 Accord. I bought the new ones at the local Advance Auto Parts store; Part No. H17 and Part No. H18 . I combined a high tone and low tone horn. I like the sound.

[Gemini2003]

Thanks!!


Had a good chat with the shop today...

Added a couple things to my list:

- Re-install Heater
- Make horn work

New:
Re-add cat converter
likely need to replace my front rotors, I'd bet the grooves are more then 2.3 mm deep.


QUESTION:

Do the stock standard accords have a neutral safety switch?

[redaztec]

Nice work!

I believe the standard Accords did come stock with a neutral safety switch - I know my 89 has one.

[EricW]

QUESTION:

Do the stock standard accords have a neutral safety switch?

My 86 manual trans didn't have a clutch switch.

Sent from my MB860 using Tapatalk 2

[dieselgus]

Good to see more progress being made, I always really liked that orange colour... BC inspections do suck, when I had to get my Accord inspected for out of province I ended up having to go to a buddies hook up for it as it wouldn't pass by most shops standards... So stupid though. If only you were in Van I would tell you where to go for inspection.

They are still less intense than the Manitoba one, which is mandatory any time ownership is transferred on a vehicle. But it does keep the unsafe shitmobiles the hell off the road, which I kinda appreciate. Cops over there also are pretty good about pulling over anything that looks poorly maintained and sending it for inspection. Here in the lower mainland, not so much. You gotta be pretty much speeding at least 25 over + talking on a cellphone + not wearing a belt for them to pull you over. Traffic services is pretty understaffed in most detachments that I deal with and from what I gather.

[Dr_Snooz]

The neutral safety switch got added in either 88 or 89. There has been some debate over it in the past.

[Gemini2003]

Well.... I'm going to tell them I switched all the components with an 86 model :-)

[Civic Accord Honda]

OMG so glad to see your working on her still!!!! making progress again :D

[Gemini2003]

Hey All I need help...

I Cannot get my horn to work

i've looked here http://www.3geez.com/forum/technical/44428-horn-troubles.html and here http://www.3geez.com/forum/technical/64986-horn-cruise-help.html with no luck.


I have constant power to the horn and I have tested the steering wheel. When I depress the steering wheel it

***HOLD UP ***

As I was writing this I was like ummm....hornS? I thought there was only one.... low and behold hooking up the second horn completed the circut and I have working HORNS now.





This leaves me with Blower motor. Lets get you working now

[Gemini2003]

So Yeah Update:

Horn is fixed,

Blower motor is kind of running.... I think it's toast and needs replacement... sounds like a whole tree is in side the blower motor lol


AND I relocated my battery :-)

http://geminiwebhosting.ca/images2/relocated.jpg


I just need to fix my fuel lines now :-) and switch my tires over... Not much left!

[Tdurr]

that bay looks good man! I love it. Ill read threw this again, but where did u get that strut bar again?

[Gemini2003]

Hahahahaha I dont know!

I'm thinking it was an Ebay find I'll have to dig deeper :-)

[Gemini2003]

I can't remember where I got the front strut tower brace from I'm pretty sure it was EBay from someone on here.

I installed a new to me blower motor today :-)

Leaving Fuel lines needing to be secured to the body of the car and swap tires... Bring on the Safety!

[MessyHonda]

looking good

[Gemini2003]

So I'm putting in a few minutes here and there... Christmas really killed me for cash flow :-(

I finished relocating the Battery to the Trunk :-) The 2ga power wire was only $30

I need to buy Fuel line fasteners Now... and it's probably easier if I put my Honda steelies back on :-)


Another week or so I hope!

[Gemini2003]

A little picture update:

http://geminiwebhosting.ca/images2/battery.jpg

http://geminiwebhosting.ca/images2/battery2.jpg


I Know I Need to be using a different battery that's the the mounting isn't permanent yet.


http://geminiwebhosting.ca/images2/headlightdone.jpg

My passenger headlight was damaged. Replaced :-)

I also re-installed the ducting under the dash, confirmed it's defrosting my window now :-)

[Gemini2003]

I found out that the tires and rims on my 02 accent fit our cars .... Bonus! Means I save a hundred bucks on getting new tires as I had an extra set on rims in storage :-) I had to replace tires anyway to pass safety :-)

http://geminiwebhosting.ca/images2/2014-01-06 01.59.26s.jpg

So beautiful here today... got to roll the car out and start her up... Brought it up to temp and the heater blew warm air on the window!! so now I'm guaranteed 100% done finished without a doubt now haha felt good to get this project off the list :-)


After I finished that Lordco called My fuel line fasteners/hose clamps came in :-)

http://geminiwebhosting.ca/images2/2014-01-06 02.00.50s.jpg

So, the car is jacked up and I'm ready to start securing the fuel line.... almost done :-)

[Gemini2003]

Poo.

Just figured out I have something I Need to complete first before putting my fuel lines back in.

All the rust repair I did ( wheel well front passenger tire, Floor pan under read driver passenger feet) ..... well I didn't complete it all apparently (now that i"m crawling under to secure fuel lines >:-\ ).

So now I have to go to Lordco once again and purchase Rubberized Undercoating in a spray can. This way I can fill in the one spot and eventually cover everything up so none the wiser :-)

http://geminiwebhosting.ca/images2/2014-01-09 11.06.11s.jpg
http://geminiwebhosting.ca/images2/2014-01-09 11.07.21s.jpg

[Gemini2003]

Before
http://geminiwebhosting.ca/images2/2014-01-10 12.54.33s.jpg

Before (Sanded)
http://geminiwebhosting.ca/images2/2014-01-10 13.15.59s.jpg


First Coat
http://geminiwebhosting.ca/images2/2014-01-10 14.08.03s.jpg

Second Coat:
http://geminiwebhosting.ca/images2/2014-01-10 15.57.21s.jpg

Mostly Dry:
http://geminiwebhosting.ca/images2/2014-01-10 15.59.56s.jpg


Rear Passenger floorpan underside Sanded and ready to be sprayed
http://geminiwebhosting.ca/images2/2014-01-10 14.08.59s.jpg
http://geminiwebhosting.ca/images2/2014-01-10 14.09.14s.jpg

First coat
http://geminiwebhosting.ca/images2/2014-01-10%2014.22.58s.jpg

It's drying... or was when I left the house today :-)

So after doing these area's I now have to coat the entire underside of the car to make these spots blend in :-) Looks good tho :-)

[Gemini2003]

Driver Side Front Before Clean
http://geminiwebhosting.ca/images2/2014-01-12 11.08.53s.jpg

Driver Side after (wet)
http://geminiwebhosting.ca/images2/2014-01-12%2012.24.51s.jpg



Driver Rear Before Clean
http://geminiwebhosting.ca/images2/2014-01-12 12.03.09s.jpg


Driver Rear after (wet)
http://geminiwebhosting.ca/images2/2014-01-12%2012.24.33s.jpg



I know like who cares right? haha posting pictures keeps me motivated :-)

[Gemini2003]

Rear Passenger wheel well done.


http://geminiwebhosting.ca/images2/2014-01-13 11.55.26s.jpg

http://geminiwebhosting.ca/images2/2014-01-13 12.10.58s.jpg


Just need to finish spraying the underbody and then I can attempt to secure the fuel lines :-)

Hopefully I'll have this done tomorrow.

[Gemini2003]

Well the rest of the car is sprayed, thank goodness we are breaking heat records here in Kelowna! +15c here yesterday (59 Fahrenheit you Americans :-P)
http://geminiwebhosting.ca/images2/all.jpg

[Gemini2003]

http://geminiwebhosting.ca/images2/20140114_1327372.jpg
^Front passenger side looking back

http://geminiwebhosting.ca/images2/20140114_1328092.jpg
^front driver side looking back

[Civic Accord Honda]

much win!!!!

[Hazwan]

Looking good! Sucks about that rust spot on the fender though :(

[Gemini2003]

Meh, not so bad,

$15-20 at the local Pick-n-pull for a new one :-)


I have to paint the whole car yet anyway

[Gemini2003]

http://geminiwebhosting.ca/images2/2014-01-18 19.52.28s.jpg
From the fuel rail going through the Firewall
http://geminiwebhosting.ca/images2/2014-01-18 19.51.34s.jpg
Down to the left under the insulation along the bottom of the door.
http://geminiwebhosting.ca/images2/2014-01-18 19.49.02s.jpg
All secured all the way to the back, Used a small drill bit and self tapping skrews
http://geminiwebhosting.ca/images2/2014-01-18 19.48.06s.jpg
Pops through under the rear passenger seat


http://geminiwebhosting.ca/images2/2014-01-18 19.56.45s.jpg
I moved the fuel filter to the Gas Tank, I dont know why it's just not under the hood anymore lol


http://geminiwebhosting.ca/images2/2014-01-18 20.37.24s.jpg
I had 3 extra fasteners, This is the positive power cord running on the passenger side of course :-) It's just sitting loose here no battery...
http://geminiwebhosting.ca/images2/2014-01-18 20.37.18s.jpg
Temporarily ran like this I had lots of extra 2ga Power wire



So i'm basically done. I have more Rubberized sound dampener so that is what I'm going to finish today... put the wheels back on and go for a test drive

[Gemini2003]

*Le Sigh*


So.... even tho the parts store sells rubberised fuel injection line it's not legal to have it as fuel line. Like WTF.

SO.... I need to put in the Steel line in, I didn't have this line originally becuase this car started life as a Carb model... so no fuel return line to the tank.

I wish I read this closer: http://www.3geez.com/forum/how/112-convert-carbureted-fuel-injected.html

[Gemini2003]

When I started this poor EXI was in good shape....



3 hours later.....
http://geminiwebhosting.ca/images2/oops.jpg

I had to pull: rear seat (most of it), driver seat, carpet on the driver side of the car, the dash, the heater core the steering colum, the pedals and thefirewall insulation

[VIPER1988]

Like the orange color. Looks good. Think you need a new box for your blower. lol

[Gemini2003]

haha the pitcure is of the car at the wrecker not my baby... mine actually looks worse some how at this second... But I'm off work now so.. .. here I go!

[Gemini2003]

So, I got at her last night again,

Drilled a hole in my firewall for the new line,
Installed the steel fuel line and secured it all the way back
Re-installed the firewall insulation
Re-installed the Wiring harness
Re-installed the Blower Motor
Re-installed the Heater core

[Gemini2003]

Re-installed the Duct between Blower and Heater Core,
Re-installed the steering column
Re-installed the Dash and Gauges
Re-installed the Pedal assembly

After all this I went to go test my brakes... no brake lights :-(


So, I went back a couple pages to my self done safety inspection and I found I had no brake lights then either...



I'm definitely going to the year to grab one I called the glass shop today and they said 500 bucks.

So I just safetied my car myself:

http://geminiwebhosting.ca/images2/20131107_183302_resized_11000pix.jpg





Which.... Means..... I was driving around town with no brake lights..... For a while... awesome....

http://www.3geez.com/forum/technical/90554-brake-lights-not-working.html


Great Thread for Brake light troubleshooting. :-) Sticky?

I had the same issue, thanks to the above post I visually inspected my fuses and found bad ones,

The other issue however, my brake switch didn't have 4 pins mine had 2.


I think the difference is between cruise and non cruise,


I need the different switch for my brakes I just realized, off to the wrecker I go lol


**EDIT** I'm back and simply switching the switch on the brake pedal resolved this concern, Also the wiring at the bulbs was all rusty... cleaned it all up and I have brake lights again!

[Gemini2003]

Over and over and over again I find usefull information on this site!! You all rock... Thanks again!

( I just found out that I forgot to grab the second ECU under the passenger seat of the EFi models )

[Gemini2003]

Well, As it turns out I had the relay I needed but grabbed the grey ECU box... I think it's for the power locks? Anyway my harness is happy now with no dangling connectors lol

I got my car up to 190 degrees last night, the thermostat opened and I had flow, I was happy :-)

No fan running tho... and considering it's -15 to -10 C (5 to 15 F) right now I doubt it's going to get to the 220 degrees Fahrenheit needed for the fan to turn on.

I did the "Jump the temp sensor at the bottom of the Rad test" and my fans kicked on :-)


WOOOOOOOOOOOOT!!!


I may be ready for safety!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!

[Gemini2003]

Dang lol keep running into snags found out my reverse lights are not working I have connected the two wires off the tranny to the Green/black and yellow at the automatic shifter location, still no reverse lights.


Going to grab a couple sensors from the wrecker tomorrow to check that.


Got some odds and ends today. Resolved my brakes issue for real this time haha feel like I run into every issue I can with this car. All in the learning I guess All Bulbs and wiring at the tail lights replaced and the 3rd brake light bulb replaced as well. No more warning light on the dash every time I hit the brakes :-)

The temp sensor on the top of the motor was rotted, replaced that today as well.

Here are my upgrades I cleaned them up using sandpaper and then toothpaste :-)
http://geminiwebhosting.ca/images2/four.jpg

on:

http://geminiwebhosting.ca/images2/2014-02-08 15.09.44s.jpg






I dont have the right bumper at this point, some modification to the bumper needed to be done but they press fit into the bumper real nice :-)
http://geminiwebhosting.ca/images2/2014-02-08 17.56.54s.jpg

^ TEMPORARY until after the inspection

[Tdurr]

Great work man! Glad you are getting this bad boy road worthy still. What all do you have left?

[Gemini2003]

Going for a test drive this morning...but not much!!!!!!!! like... maybe ... oh i need to replace the lock on the driver door :-)



Yesterday I fixed my reverse lights, I was having the damndest time gettin gthem going after the swap.

I read http://www.3geez.com/forum/technical/72098-additional-notes-mt-swap.html

and I put the wires together but again like other have said no power to the Switch.

I ended up running a wire from the tranny to the interior fuse box. From Fuse #2. This new wire is the yellow wire. I ran the other half of the switch directly to the wiring harness. In my case I spliced it into the harness right beside the drive seat.

Reverse lights work again!!.... spent ALL damn day on that one.

[Gemini2003]

Yay! Pulled her out of the shop and ripped around the neighborhood for a bit darn thing never went above 180-190 degrees F Good I know :-) lol

No shifting issues, no issues with the cv's as far as I can tell.

I have an issue with my headlights intermittently not working on high beam very weird.

I relocated the battery BACK to the engine bay. Re-installed the battery try of course as well.

Tightened up the Front bumper and Bumper Cover.

Buttoned up all the dust shielding under that area as well.

Tidy'd up most of the wiring harness with electrical tape and Zap Straps.



once I figure out the headlight intermittency issue ... and maybe bleed my brakes...... I am pretty sure it's 100% time for safety!!

[Gemini2003]

Headlights are still being intermittent, but most of the time they work... like 1 in 5 times the high beams don't work.

Tested my Hazards (forgot to last time) and they're also working..... Even tho they take a few seconds to activate.


I need to:

Get weather stripping for one of my doors,
Replace all the grommets on the firewall
repair a small bit of body work at the rear driver passenger door.

Just when I think i'm done it's like FU!! MORE WORK!! lol "ok ok ok soon enough I'll be done!

[Civic Accord Honda]

YAY FOR PROGRESS!!!!!!!!! atleast the list of work that needs to be done isnt to bad ! sounds like she will be back on the road in no time :)

[Gemini2003]

The body work I tackled today:

The weld i need to hide:
http://geminiwebhosting.ca/images2/2014-02-15 15.29.49s.jpg
http://geminiwebhosting.ca/images2/2014-02-15 15.30.29s.jpg
http://geminiwebhosting.ca/images2/2014-02-15 16.08.20s.jpg


After a grind with a wire wheel-angle grinder setup & The rust holes I uncovered:
http://geminiwebhosting.ca/images2/2014-02-16 12.16.21s.jpg


Cut away most of the rust:
http://geminiwebhosting.ca/images2/2014-02-16 13.17.41s.jpg

http://geminiwebhosting.ca/images2/2014-02-16 13.17.49s.jpg

Put on some fiberglass
http://geminiwebhosting.ca/images2/2014-02-16 15.57.27s.jpg

[Gemini2003]

First coat of resin:
http://geminiwebhosting.ca/images2/2014-02-16 14.40.21s.jpg
http://geminiwebhosting.ca/images2/2014-02-16 14.42.50-1s.jpg

More Fbreglass:
http://geminiwebhosting.ca/images2/2014-02-16 15.57.27s.jpg

Send coat of resin:
http://geminiwebhosting.ca/images2/2014-02-16 16.21.54s.jpg

[Gemini2003]

Wow, over 50,000 views thanks guys!

[Gemini2003]

From this:
http://geminiwebhosting.ca/images2/2014-02-16 16.21.54s.jpg

To This:
http://geminiwebhosting.ca/images2/2014-02-17 11.17.09s.jpg
http://geminiwebhosting.ca/images2/2014-02-17 11.16.59s.jpg


To this: Ready for Bondo/Primer
http://geminiwebhosting.ca/images2/2014-02-17 11.55.11s.jpg
http://geminiwebhosting.ca/images2/2014-02-17 11.55.23s.jpg

[Gemini2003]

Taped and Primed:
http://geminiwebhosting.ca/images2/2014-02-18 10.51.54s.jpg
http://geminiwebhosting.ca/images2/2014-02-18 10.52.01s.jpg

Little run fixed where the Weld was:
http://geminiwebhosting.ca/images2/2014-02-18 10.52.03s.jpg

Taped and sprayed the Rubberized undercoat:
http://geminiwebhosting.ca/images2/2014-02-18 11.08.53s.jpg

The Reveal:
http://geminiwebhosting.ca/images2/2014-02-18 11.47.49s.jpg
http://geminiwebhosting.ca/images2/2014-02-18 11.49.18s.jpg
http://geminiwebhosting.ca/images2/2014-02-18 11.49.40s.jpg

[Gemini2003]

From this:

http://geminiwebhosting.ca/images2/2014-02-15%2016.08.20s.jpg


To this:

http://geminiwebhosting.ca/images2/2014-02-19 09.17.13s.jpg
http://geminiwebhosting.ca/images2/2014-02-19 09.17.24s.jpg

[Gemini2003]

Pulled it out (gigiddy)

http://geminiwebhosting.ca/images2/2014-02-19 10.44.28s.jpg
http://geminiwebhosting.ca/images2/2014-02-19 10.43.50s.jpg

[Gemini2003]

So I took it for a test drive that day,

Battery light is on.....

Pulled the battery cable with car running and it died,

Altenator toast :-( Picked up a new alt today from the junker and replaced it, Test fire tonight when I get off work :-)


If the alt is fine and the headlights are working normally I Think I'm ready for safety...I think lol

[Gemini2003]

Alternator is fixed :-) Headlight switch 50/50 so im just going to just try i think, quick test drive tomorrow but i honestly think that's it i'm applying a couple more coats of the undercoat just to hide a couple more little spots :-)

[Gemini2003]

SOB.... My gas gauge isn't working, I'm going to fix that before bringing it in.... Man I tell you this safety is getting annoying....

[Dr_Snooz]

Try a California smog check.

[Gemini2003]

Hooked up my new Gauge Cluster..... Headlights wont work now... FML lol..... Well fuck haha this car.... I tell ya... hahaha

A few pictures just because:

http://geminiwebhosting.ca/images2/a2014-03-05%2021.34.54.jpg <--- Me and my Heated Shop/garage/playground lol

http://geminiwebhosting.ca/images2/a2014-03-05 21.34.54.jpg



Ratcheting box end Wrenches <3 <3 <3 <3 <3 <3 <3 <3 <3 <3 <3 <3 <3 <3 <3

http://geminiwebhosting.ca/images2/a2014-03-06 12.47.22.jpg


Need a Socket?
http://geminiwebhosting.ca/images2/a2014-03-06 12.48.35.jpg

[Gemini2003]

http://geminiwebhosting.ca/images2/2014-03-09 15.52222.JPG



I only checked this myself so time to bring it in :-)

[Tdurr]

good luck man!

[Gemini2003]

Well, I failed but all this is easy to fix all the electrical shit passed :-) :-) Off to the wrecker in the am :-)

EDIT just priced this all out at the wrecker and it's going to cost about 250 before tax if I get everything individually, however I think if you take the works they give you a discount AND it's easy lol maybe get them down to 150-200 :-)


http://geminiwebhosting.ca/images2/111r.JPG
http://geminiwebhosting.ca/images2/222r.JPG
http://geminiwebhosting.ca/images2/333r.JPG
http://geminiwebhosting.ca/images2/444r.JPG
http://geminiwebhosting.ca/images2/555r.JPG

-Michael

[Dr_Snooz]

Wow. I can see ball joints and brake pads, but hood rods and seat belt holes? You have to be kidding me.

[Tdurr]

lol whatttt

[Dr_Snooz]

We don't have safety inspections of any kind here in California. We also drive very old cars because there is no rust or harsh weather to destroy them. Yet somehow we don't have massive casualty counts from our seat belt holes or missing hood props. Heck, we have ball joints come apart on the road and there are no giant pile-ups. How do they justify forcing everyone to pay for those inspections up there? Are there any hard numbers to support the scheme?

[gyates93]

It's all about $$$$... Some provinces up here require YEARLY safety inspections. One rust hole, exhaust leak, or dead light bulb will cause a failure. Also, my auto registration sticker costs $140 per year..

At the same time, this car has multiple serious issues.. Ball joints, wheel bearings, brakes, tie rod end.. Yeah, I wouldn't have wasted my money on the inspection.

[dieselgus]

The reason the officer requested the major inspection was because it was probably deemed unfit for the road, and frankly looking at all of the issues, I probably would too. Something must have really pissed off the cop, or the car had blatantly obvious mechanical issues that got the cop worried enough to force an inspection. Gets the unsafe and sketchy shit off the road. Not really a cash grab as it forces slackers to fix their death traps properly so that a mechanical or structural failure on the death trap does not cause a major accident and wipe out some other unsuspecting motorist.

I think inspections are a wonderful motivator to keep a vehicle in good working order at all times. I hope they start doing them yearly actually, instead of Aircare/smog.

Just my .02

[Hash_man_Se_i]

Some of those shops in BC are retarded for the stuff they mark as unsafe... First inspection I took my car for in Van, the guy said my seatbelts failed because they didnt recoil under no tension fast enough... Yet acknowledged that the locking mechanisms and buckles worked perfectly well. It's a 25 year old car... not a new car. He also said my car wouldn't pass with some buttons/switches not in the dash and their holes open... how is that a safety issue if I don't have a blank where the cruise control switch is supposed to be??.... So I found another shop through a friend and passed without any issues.

Good luck getting yours sorted and getting through the inspection.

[Gemini2003]

Well...


I did piss off the cop BUT not intentionally

My car had no visible rust but it's Primer Grey n Orange and it's lowered so it does look heatscore.


What it was in the end was the cop was dumb to what makes a car road legal or not.

He Pulled me over for FAILING TO YEILD (which I admitted to) and saw that I had no seats except my driver seat and he had a Kanipshit.

Once I told him that you legally did NOT need seats beside the driver seat he thought I was lying to him. He called his traffic cop buddy and I heard him say " well he needs seats doesn't he? " LOL

Anyway he let me slide for the fail to yeild but hit me for a Box 1 Vehicle Inspection






I have not worked on the car since the day of safty, I'm going to pick it up again in the next week or so...

Right now however I've got a serious.....serious.... addiction to minecraft... lol

[Gemini2003]

Happy 420 Everyone!!!

[Gemini2003]

http://geminiwebhosting.ca/images2/reciept.jpg


Look at the Price!! It was a Great day @pnp!

[niles]

Love that place!

Sent from beneath a 3Gee with a wrench in the other hand

[Gemini2003]

I'm slowly re-installing all the stock suspension to get past safety, sooon.....

[Gemini2003]

*update*

My Shop ready for more Project work!

http://i.imgur.com/fBc9d2R.jpg

I created a list of safety inspection:

- NO second VIN
- Hood Support Bar
- All seat belts without seats will need to be removed
- On the floor where seat belts and seats were mounted - Holes will will need to be filled (gigiddy)
- Both Rear upper Ball joints
- Left front control arm worn out
- Pass side outer tie rod end worn out
- Power steering will need to be put back in
- Front shocks worn out
- Rear shocks worn out
- Rear tires
- Front brake pads
- Rear brake drums
- Front brake lines will need to be secured
- Pass Front wheel bearing worn out

[Gemini2003]

Progress so far:

I created a list of safety inspection:

Fixed - He was dumb, Found this on the firewall and the dash - NO second VIN
Fixed - Hood Support Bar
Fixed - Left front control arm worn out
Fixed - Pass side outer tie rod end worn out
Fixed - Front shocks worn out
1/2 Fixed - Rear shocks worn out
Fixed - Rear tires
Fixed - Pass Front wheel bearing worn out


More to go tonight!:

- Front brake pads
- Rear brake drums
- Front brake lines will need to be secured
- Power steering will need to be put back in
- All seat belts without seats will need to be removed
- On the floor where seat belts and seats were mounted - Holes will will need to be filled (gigiddy)
- Both Rear upper Ball joints

[Gemini2003]

Done:

- Rear brake drums
- All seat belts without seats will need to be removed
- Both Rear upper Ball joints

To go:

- Front brake pads $45
- Front brake lines will need to be secured
- Power steering will need to be put back in - I dislike this.
- On the floor where seat belts and seats were mounted - Holes will will need to be filled (gigiddy)
- Need 2 bolts for my shocks in back, and the one bolt for the bottom of the shock thru the lower control arm.

[Gemini2003]

- Front brake pads Free! found new ones at pick n pull... also new rotors 10.99 each
- Front brake lines have been secured
- Power steering will need to be put back in - I dislike this.I''m going to try to not do this
- I filled the holes on the floor where seat belts and seats were mounted - with stock bolts :)
- I Grabbed two decent shocks :-)

[MessyHonda]

we want pics

[Gemini2003]

This post was not required