revival of a old header

[SQ is the SQUAD]

back in the day, i ordered a pasesteer exhaust for my hatc from nopi. long story short i had a dx coupe and they sent me lxi coupe stuff. i ran the exhaust system on my hatch after hondaman87 made a slight adjustment to the exhaust pipe for me. i never really drove the car. anyways, as we all know, the pacesetter headers need to be recoated to last, i dident recoat mine. after i stop using the car they rusted.

fully rusted state
http://img74.imageshack.us/img74/7130/picture1700mk.jpg

http://img74.imageshack.us/img74/8158/picture1447iv.jpg

here it is after i wire brushed it with my rotor tool and air compressor
http://img74.imageshack.us/img74/8734/picture1744ip.jpg

http://img74.imageshack.us/img74/2057/picture1733dt.jpg

i picked this stuff up from work, works great. i also used pb spray, a wire brush, and some sand paper
http://img74.imageshack.us/img74/9139/goodstuff1pa.jpg

here is the de rusated header
http://img108.imageshack.us/img108/1795/norust11pd.jpg

http://img108.imageshack.us/img108/1214/norust26dx.jpg

http://img108.imageshack.us/img108/9503/norust32ak.jpg

and finally the header after it was washed with soap and 3 coats of 1200 degree flat black paint
http://img74.imageshack.us/img74/3286/painted7lc.jpg

[88Accord-DX]

Let me know how hard that EGR pipe is to get off & post some pics after you take it off. Would like to know. Here is a post in your other thread too.


Hey bro let me know if your paint sticks I used the same stuff after the car is started mine bubbled up and now it's slowly chiping off.

[SQ is the SQUAD]

as you can see the piping nut is chewed up. i forget what i had trouble with but it dident want to come of the factory pipe i think it was. hopefully this one comes off no problem. i am going to clean up all the holes and get new o2 sensors.

[86-accord-lxi]

You saved it from cancer, Looks good ! Are you going to keep it, or sell it ?
I am in the market for a header, But don't have a lot of extra cash at this time. I have an 89 lxi parts car, Would you trade the header for any particular part, or parts ? That is if you aren't kepping it. :)

[SQ is the SQUAD]

i was going to sell it but i recently brought an 89 lix coupe, so i am going to throw it on there for now. once i bould my turbo manifold, i will no longer need it and i will sell it

[88Accord-DX]

It'll take a medium size pipe wrench & getting the EGR nut cherry red with a torch (propane or welding) to loosen it up. Tighten it first & then try to loosen it.

[SQ is the SQUAD]

damn, maybe i should of taken it off before i painted it

[mkymonkey]

looks good, what type of paint did you use?

[bobafett]

fair warning, to get the EGR off of my DC, which was driven alot but never left to rust, it busted the whole peice off of the manifold, it had to be retapped and the elbow welded back on. :(

[SQ is the SQUAD]

when i get home from school today that might be my first project

[snoopyloopy]

looks much better than before. how far into the inside was the rust?

[SQ is the SQUAD]

i belived it went all the way down the runners. i lubed all the runners up oretty good with the rust remover

[89AccordResto]

Think sandblaster.

[SQ is the SQUAD]

i gotr the egr pipe out pretty easly. its ready to bake in the oven!

[SQ is the SQUAD]

i just got finished letting the header bake in my overn at 350 degreezs. the paint is nice and dry. hopefully it last for a while

[carotman]

That permatex stuff seems to do the job quite well!!

[SQ is the SQUAD]

tell me about it. i got a bunch of motor bolts i am going to let sit in it for a while to see how they turn out. ill take before and after pics

[A20A1]

I coated my stock manifold once when it was still on the motor... I cleaned it up, ran the car and sprayed the duplicolor on and it hasn't peeled.

I think I should have done the same to my custom header.

[SQ is the SQUAD]

just waiting to get new gaskets before i put my exhaust on