Alright FINALLY Built engine parts?

[AccordEpicenter]

Heres what im thinking, .20 or .30 over diamond forged pistons... what was the part number on those? How do you contact them? I searched but couldnt find shit. importperformanceparts.net has the toga main and rod bearings, toga oil pump, eagle H beams, and head studs for $666.00... Sound like a good deal?

[AccordEpicenter]

true. Ive heard the same for scat h beams too

[smufguy]

eagle rods are pretty good. i think the stock wrist pins are 19mm and the stock dimond forged pistons.............. well i have the part number at home. ill get u that when i get there.

[Kabuki]

The stock wrist pins should be 20mm for the A20A and B20A3. The B16/18 wrist pins are 21mm, and the B20A/B21A, F, H, and K Series are all 22mm. If your rods use larger pins than your choice of pistons, then you can use the smaller pins that match the pistons and have a machine shop fit the rods with bushings. It's a very common thing in the domestic world, and comes stock on many engines.

[smufguy]

i meant to say 19mm, sorry guys

[AccordEpicenter]

is that a mitutoyo or a knockoff? I have an analog mitutoyo but i had a digital one at the lab that measured to .0005"

[gfrg88]

i still dont get this, why can we use b18 rods but we cant use their pistons???? im lost when it comes to this :dunno:

[AccordEpicenter]

The b18 pistons dont have the wrist pin in the right area (wrist pin height) so the pistons wont be even close to where they need to be in the cylinder

[gfrg88]

so wich pistons is adam using??? he has JE pistons are they a custom order??

[bobafett]

i have diamond pistons that were custom orders.

other than off the shelf applications that are pre stocked, most piston manufacturers can and will do custom orders for anything. you just have to get very specific on exactly what you want. :D

[smufguy]

so wich pistons is adam using??? he has JE pistons are they a custom order??

he runs a B20a motor with a different bore size than our A20. there could be a reason why he is able to run off the shelf pistons and we cant.

[mkymonkey]

uh...no i think he sold the b20 and now has a turboed a20

[gfrg88]

actually Praveen, Adam doesnt have his B20 anymore. hes using Justins old A20, his new setup is awesome!!!

[AccordEpicenter]

alright i called diamond today... and the guy i talked to (i think it was mike?) said that the job number i had for military mase's pistons was for 20mm wrist pins, not 21mm? WTF? He also quoted me $580? I used job 20809... is that the right job number? Mase- Jump in here lol.

[smufguy]

damn, that tells me how much i am laggin on this board these days............... :: goes back to sleep ::

[AccordEpicenter]

alright updates: I got all my honda parts here (seals/timing belt/o rings etc/waterpump) ordered the diamond pistons. Apparently brian (military mase) had originally ordered 20mm wrist pins but went to 21mm wrist pins later (ron remembers him and the job!! and he remembers Chris and Sean!!) ron is sooo the man. If i do another build up i will def go to him. I should have these in 2 weeks or so he says. And yea the pistons were $360 alone but i got the good rings and fitted wrist pins so that pushed it to like $450 or somthing but thats really not bad at all, esp for custom pistons!! Looks like the crank situation is solved. Now all i need is to get the block bored, get headstuds/mainstuds, bearings, toga oil pump and eagle rods and this motor is going together!

[bobafett]

fuck yeah man! ron and eric are the guys that I worked with. they were very helpful!

good luck with your setup man!