View Full Version : what type of ball joints to buy
alboy86
02-06-2007, 05:21 PM
well gunna take on the lower ball joints tommarow any good brands of bjs to buy
HondaBoy
02-06-2007, 05:30 PM
moog are good, Honda if you can afford it. i'm needing to do mine also. i plan to just get some from O'reilly auto parts, making sure they have a lifetime warranty.
lostforawhile
02-06-2007, 05:32 PM
the moog are good,you can order them from summit too.
alboy86
02-06-2007, 07:41 PM
ill just go with some with lifetime warrenty they have some and pep boys ill check out
88Accord-DX
02-06-2007, 08:35 PM
Moog. Don't mess with anything else than maybe OEM Honda 'bend over & take it, with the price ball slapping on your ass.'
Vanilla Sky
02-06-2007, 09:42 PM
MOOG!! they're all i'll use unless i'm dead broke and need the part replaced right NOW. never had a failed moog. i've seen pretty much everything else from parts houses fail in 10,000 miles or so. everyone i know that's had experience with trying to find a joint that lasted in their car ended their search when they installed moog balljoints.
MessyHonda
02-06-2007, 09:45 PM
i bought my moog lower ball joints for 30 bucks a pop
LX-incredible
02-06-2007, 10:04 PM
Moog. They come with polyurethane boots, so they last. That last set that I bought were made by meyle, or something like that. Joints were quality, passenger side boot split after 3 or 4 weeks.
alboy86
02-07-2007, 09:07 AM
dam where did you get them for 30 bucks each
MessyHonda
02-07-2007, 09:59 AM
rockauto.com
alboy86
02-07-2007, 01:06 PM
i bought one at kreagen its Mcquay-norris the guy at the store was like does your car even have ball joints then they gave me one for a voltswagon good thing i checked the box before i left
alboy86
02-07-2007, 01:07 PM
oh and what size is the CV nut i dont have a socket to fit it and was wondering what size
MessyHonda
02-07-2007, 01:09 PM
oh and what size is the CV nut i dont have a socket to fit it and was wondering what size
32
HondaBoy
02-07-2007, 02:24 PM
looks like i will be going with the Moog ones, Honda is a little expensive with those parts.
alboy86
02-07-2007, 04:03 PM
quick question which way loosens the cv nut im trying to get it off and i wanna make sure im pulling the right way
nswst8
02-07-2007, 04:16 PM
Counter clockwise to loosen. Its a standard thread. Use a good size breaker bar I usually use a 3/4" with either 1 1/4" / 31/32mm socket. Keep the tire on the car leave it in gear w/ e-brake on and don't jack up the car before loosening the CV axle nut.
alboy86
02-07-2007, 04:26 PM
sweet cause im puttin all my effort into it and it aint coming out
MessyHonda
02-07-2007, 05:00 PM
i used the jack pole as a breaker bar...also make sure the lil part where its dented is straight to take it out
alboy86
02-07-2007, 05:35 PM
:Owned: ya i think i just need a bigger bar to get more leverage i gave up for now i think my upper arms are worse anyways the lower one is bad but it still has some grease in it and the boot isnt flat
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.