fogs and front lip

[87SIA20A3T]

1) can you bolt a front lip off a acura integra directly to the bumper of a 3g
2) If you have them, where did everyone get those yellow fogs that seem to fit conviently in the little vent looking deals under the bumper?

[carotman]

Those are JDM fogs. I was able to find clear ones that are exactly the same. I haven't found any other pair yet.

[Civic Accord Honda]

i got yellow ones that fit great under there but i had to make a bracket for them to work there really old Kmart brand fogs i got off ebay

[Pico]

1) can you bolt a front lip off a acura integra directly to the bumper of a 3g

not directly but it will mount up with a little bit of help

[86ccord]

i bought some from advance autoparts last night and they would of fit nicely if they were the ones i wanted... would of kept them if i could change the bulbs out...oh well..

[LxAcc510]

i bought some from advance autoparts last night and they would of fit nicely if they were the ones i wanted... would of kept them if i could change the bulbs out...oh well..

Where's advance autoparts? Are you referring to a store? or a website?


Whoops nvm, found the site. =P

[87SIA20A3T]

Are those actualy in the spot where the dumby plastic thing or are they just bolted to the bottom of the bumper?

[epic1400cs]

I am not sure if you are interested but just in case, I have made light bracket which is copy of Cibie's bracket for our early model (86,87) car.
These are two piece and very very rigid.
I made out of stainless steel but you can make it with steel, too.
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_128_full.jpg
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_129_full.jpg
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_156_full.jpg
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_155_full.jpg

For more pic, please try
http://www.cardomain.com/ride/783843/5

[ghettogeddy]

I am not sure if you are interested but just in case, I have made light bracket which is copy of Cibie's bracket for our early model (86,87) car.
These are two piece and very very rigid.
I made out of stainless steel but you can make it with steel, too.
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_128_full.jpg
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_129_full.jpg
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_156_full.jpg
http://memimage.cardomain.com/member_images/3/web/783000-783999/783843_155_full.jpg

For more pic, please try
http://www.cardomain.com/ride/783843/5

omg how much shipped to California 94509 usa

also were can i get the lights

[epic1400cs]

omg how much shipped to California 94509 usa

also were can i get the lights
It will be ridicurously expensive so you prefer to DIY it I believe. :D

[epic1400cs]

also were can i get the lights
Was about $10 on ebay.
They are very old BOSCH driving light from 80's.

[ghettogeddy]

Was about $10 on ebay.
They are very old BOSCH driving light from 80's.

if you find another set shoot them my way and yes a diy would be fine but those brackets would fit in a small bubble wrap package and shouldent cost more then 10-15 bucks to ship

[jdmaccordnut]

not directly but it will mount up with a little bit of help

I snagged one at a junkyard for $7. It fits...sort of. It's really about 1" too short, on the sides, so you have to stretch it. It definitely takes two people, and some muscle to try to get it on. The bad thing is that it goes so far UP the bumper.... it'd look better with a spacer so it sat lower. Mine covers up the bottom edge of my fog/brake vent holes.

[frantik]

which 3gee bumper do you have? the LS/RS teg bumpers fit 88/89 3geez perfectly if you use a 1" nylon spacer

[rfiks]

good ryte up