I found the hand box and the glass box in the internet.

[Tommy AC89 Thailand]

I found the hand box and the glass box in the internet.
I really want its...
http://rcw.ms/forums/attachment.php?attachmentid=1255286&stc=1&d=1236324130
http://rcw.ms/forums/attachment.php?attachmentid=1255287&stc=1&d=1236324179
http://rcw.ms/forums/attachment.php?attachmentid=1255293&stc=1&d=1236324303
http://rcw.ms/forums/attachment.php?attachmentid=1255311&stc=1&d=1236325258
http://rcw.ms/forums/attachment.php?attachmentid=1255312&stc=1&d=1236325336
http://rcw.ms/forums/attachment.php?attachmentid=1255313&stc=1&d=1236325426
http://rcw.ms/forums/attachment.php?attachmentid=1255316&stc=1&d=1236325548

[lostforawhile]

i have one of those, the only problem is the point where the top attaches to the bottom section is weak and breaks,i made reinforcements for mine. you will need the metal u shaped bar that fits under the rear section also. you remove the ash tray from the back of the center console, then it attaches to the screws that hold down the center console at the back,and the armrest part attaches to that metal bar.

[Civic Accord Honda]

Cupholders!!!!!!!!!!!!11111!!!!!

[Tommy AC89 Thailand]

I think maybe I can't install the box because, I swap H22A engine so, it can be stuck with the gear wire...

[lostforawhile]

I think maybe I can't install the box because, I swap H22A engine so, it can be stuck with the gear wire...the center console has nothing to do with the gear wire. that console fits over the manual or the automatic

[Tommy AC89 Thailand]

the center console has nothing to do with the gear wire. that console fits over the manual or the automatic

That console fits over the manual

[AccordB20A]

you can make it fit

[lostforawhile]

That console fits over the manual

I have the same console, it came out of an auto and it fits a manual fine. there is a piece that is screwed in there from the bottom.

[Ichiban]

Think he's referring to cable shifter setup?

[cubert]

Think he's referring to cable shifter setup?


thats what I got out of it...

[H2289Acc]

When I did my H22 swap I ran into the same problem. Once mounted, the cable shifter assembly sits so high that the center console will no longer fit in its original position.
I'm assuming that your cable shifter assembly is the same as mine (duh) using four bolts to mount it up? Well, my solution may seem a little pre-historic, but all I did was find a big enough socket (maybe 22-24 mm) to sit over the bolt, flush on the washer underneath in order to prevent any damage to the bolts themselves. Then I took a 5 pound hammer and went to town on each corner of the shifter assembly unitl it was low enough (and level once again) to accommodate the center console without any obstruction. In the process, you'll more than likely crack the paint around the console area and it may not look like the most beautiful piece of work when you're done, but it's the easiest way to do it without any major custom work. Besides, nobody's ever gonna see it once the console is mounted up!

Let me know if this works for you or if you come across a better idea.

BTW, I think your 3G is the SICKEST one I've ever seen!!!!! Fuckin' awesome, man! That front end looks like one from a Sentra. Which bumper and lights did you use?

Greg

[Tommy AC89 Thailand]

When I did my H22 swap I ran into the same problem. Once mounted, the cable shifter assembly sits so high that the center console will no longer fit in its original position.
I'm assuming that your cable shifter assembly is the same as mine (duh) using four bolts to mount it up? Well, my solution may seem a little pre-historic, but all I did was find a big enough socket (maybe 22-24 mm) to sit over the bolt, flush on the washer underneath in order to prevent any damage to the bolts themselves. Then I took a 5 pound hammer and went to town on each corner of the shifter assembly unitl it was low enough (and level once again) to accommodate the center console without any obstruction. In the process, you'll more than likely crack the paint around the console area and it may not look like the most beautiful piece of work when you're done, but it's the easiest way to do it without any major custom work. Besides, nobody's ever gonna see it once the console is mounted up!

Let me know if this works for you or if you come across a better idea.

BTW, I think your 3G is the SICKEST one I've ever seen!!!!! Fuckin' awesome, man! That front end looks like one from a Sentra. Which bumper and lights did you use?

Greg

Thank a lot man for your suggestion.
Yes the cable shifter assembly is the same as mine using four bolts to mount it up.
I mention about I can't installation the tape box at the console because, its was struck with the gear cable clip inside the console.
I use Uras Bodykits and Cefiro A31 clear light

[AccordB20A]

i thought the front end looked more like a r31 skyline if any of you know what they are

[Vanilla Sky]

I also think that rear console piece differs from the USDM models and the general export and JDM models.

[H2289Acc]

Thank a lot man for your suggestion.
Yes the cable shifter assembly is the same as mine using four bolts to mount it up.
I mention about I can't installation the tape box at the console because, its was struck with the gear cable clip inside the console.
I use Uras Bodykits and Cefiro A31 clear light



Ahhhh...I see! Yes, I ran into that problem too! Simple solution: I used a dremel to cut a small section out from the bottom of the tape console so it would fit over the cable clip assembly. Easy as pie! Again, it won't be pretty when you open it up, but it will still cover up that ugly clip. You'll still have a bit of space to put stuff inside (other than tapes of course...and if you still have a tape player in your car you're just as ol' school/ghetto as me! lol), not to mention the complete use of the drink tray! I'll post a pic for you later today. Let me know if you have any other problems cuz I might be able to help you out and likewise.

Greg

[H2289Acc]

Tommy,

Here's the pic I promised:

http://img183.imageshack.us/img183/5677/allondra090308003.jpg (http://img183.imageshack.us/my.php?image=allondra090308003.jpg)
By H22Accord (http://profile.imageshack.us/user/H22Accord)


Good luck!

[Tommy AC89 Thailand]

Thank a lot man for your photo.
I can imagine what is your mention.
Same as me man because, it's was stuck with the gear wire.
So, I don't wanna cut the tape box.
Or do any damage with the tape box.
Buy the glass box for install and cut inside the box is the better way to do because can't see the gear wire when you close the box.

[Tommy AC89 Thailand]

Tommy,

Here's the pic I promised:

http://img183.imageshack.us/img183/5677/allondra090308003.jpg (http://img183.imageshack.us/my.php?image=allondra090308003.jpg)
By H22Accord (http://profile.imageshack.us/user/H22Accord)


Good luck!

Yesterday I cut my tape box so, I installation the tape box already.
http://rcw.ms/forums/picture.php?albumid=408&pictureid=4047
http://rcw.ms/forums/picture.php?albumid=408&pictureid=4041

[b20a86lude]

wow very clean