PDA

View Full Version : FS 1998-2002 Honda Accord 2.3L engine parts



Jareds 89 LX-i
07-23-2009, 12:10 AM
All these parts came off of a perfect running 2000 Honda Accord SE 2.3L 4 cyl VTEC, automatic trans, engine code F23A1. All parts are clean and in perfect working condition. Only reason we replaced the engine in this car was because it had a freak issue where a tiny crack developed in the block between an oil gallery and a water jacket, pumping oil into the coolant. Other than that, motor ran absolutely perfect when we pulled it out. We did a compression test right before pulling it out and got a solid 185 psi even across all 4 cylinders. Only thing wrong with it was the block. Mileage was 161,000 miles.... this came out of my friends moms car which she has had since brand new, and always well maintained

Most (probably all) parts should interchange with all 1998-2002 Accords with the same engine. But it's always a good idea to check first to make sure

So... what I have:

Most prices are neg - make me a reasonable offer

Distributor - Honda uses two different types (TEC and Hitachi).... this is the HITACHI distributor. Comes with cap and plug wires, they're still good but kinda old - $100 OBO

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01250.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01252.jpg


Exhaust manifold - LEV emissions (ULEV engines use a different manifold) - $30

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01253.jpg

Exhaust manifold heat shield - $10

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01254.jpg

Lower block/crankshaft caps- $50 OBO

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01255.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01256.jpg

Valve cover - $20

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01257.jpg

VTEC cylinder head - perfect cond. never overheated, includes camshaft and sprocket - $175

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01258.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01259.jpg

Intake manifold (upper and lower) complete with 4 good injectors, fuel rail, and PCV valve. No throttle body, EACV or EGR valve - $100 OBO

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01260.jpg

Jareds 89 LX-i
07-23-2009, 12:11 AM
EGR valve - $25

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01261.jpg

Crankshaft position sensors - $50 (these are $274 or $499 from Napa depending on brand)

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01264.jpg

Right side (rear) engine cover - $10

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01265.jpg

Oil pump, includes both balance shafts. Balance shaft drive gear assy isn't installed, but is included - $50

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01266.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01268.jpg

Misc accessory brackets - Make offer

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01269.jpg

Upper & lower timing belt covers (no rear cover). Lower cover has a rub mark where a drive belt was rubbing against it, has a tiny hole - $10

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01270.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01271.jpg

Crankshaft timing belt and balancer belt pulleys (have keyway too) - $10

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01272.jpg

Crankshaft pulley and bolt - $25

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01273.jpg

Jareds 89 LX-i
07-23-2009, 12:12 AM
Oil pick-up - $10

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01274.jpg

Oil pan - no dents and no stripped threads on drain bolt - $25

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01275.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01276.jpg

Thermostat and housing, and water pipe - $15

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01277.jpg

Oil dipstick and dipstick tube - $5

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01278.jpg

Crankshaft complete with bearings, rods, and pistons. Since Honda uses color coded bearings for each individual rod journal, I put all pistons back onto crankshaft in the same location and orientation that they came off. Bearings still look very good. All in perfectly straight working order - $100

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01279.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01280.jpg

Throttle body, does not include MAP sensor - $30

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01281.jpg

http://i2.photobucket.com/albums/y15/thirdgenlxi/For%20Sale/DSC01283.jpg


That's all I got for now. Any questions please ask! I'll take reasonable offers