Kickin It Ol' Skool (That One-Off Build) '89 Accord Coupe

[dacantu]

Just a little walk through of the history behind the car.

In Early 1989 the car was purchased by my aunt in El Paso, TX. She owned the car until about 1997 when it was passed on to my brother.

Between 1997 and 2007 everyone in my family used and abused it.

In late 2007 (My Senior year of HS) I took full ownership of the car by having it lowered and having 50 series tires put on the 15" Konigs that were on it at the time (at this point everyone hated even sitting in the car because of the rough ride)

Since 2007 I began lurking 3geez.com and learning quite a bit about the platform and common vehicle failures (most of which i was forced to learn how to fix on my own because of lack of $, or had help from fellow 3geez members.)

The Coupe has seen many major transformations since 2007
1. Stock(ish)

2. Auto Trans went out and did a 5 Speed Swap, beginning to mod the engine with bolt ons with the little aftermarket support that the A20A3 actually has, semi riced out color scheme in the bay.

3. New wheels and dumpedness (also causing a wiring short in the loom in the fenderwell)

4. About almost a year of being parked with a bad wiring harness and a bad starter and being put back to stock

5. The new current build beginning 01/2011 which will be LONG, ONE-OFF, EXPENSIVE, but WELL WORTH IT!!!!

This project will be moving pretty fast with lots of attention to detail, lots of custom retro-fitting, and best of all a SWAP so dont stay away for too long or you might miss something.

[dacantu]

Here are some pics of the car from when the mods first started to where it is now.

Phase 1- Before any real mods began and just lots of broken, old, faded, cracked pieces had begun to be replaced with used but good parts from the JY ;)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/Danny085.jpg
Same time frame (ol' nasty bay)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0439.jpg

[dacantu]

Phase 2- Jacked up and removed Huge Stock Airbox, wiper fluid reservoir and stock exhaust manifold.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0521.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0522.jpg

Picked up a *RARE* SE-i Cupholder and Armrest and sent the Armrest out to be reupholstered
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0034.jpg

Modified and Installed a 2nd Gen Integra/DA AEM CAI to fit the bay of my CA6
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0560.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0561.jpg

Installed a *RARE* discontinued DC Sports 4-2-1 (if i remember correctly), I also began getting spray can happy here (facepalm)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0260.jpg

At this point in time my Auto Trans took a shit and I went ahead and did a 5-Speed Swap in about Decemberish 2009
(Did not document the swap)

Then I picked up a 2nd Gen Accord Valve Cover and I ended up going with a different color scheme (RICE LOL)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0055.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0060.jpg

[dacantu]

Phase 3- New Wheels
After waiting about 4 months from a local Rota Dealer here in AZ I finally received notification that my wheels were in.
Rota JMAGS 16"x7" Absolute Polish with Brand New Toyo Proxes 205/40/16s
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0756.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0757.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0754.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0753.jpg

I also managed to find this *VERY RARE* JDM Duck Bill/DuckTail spoiler specific to the CA model Accords.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0760.jpg

Here she is with the new shoes mounted on (Still not dumped at this point)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0782.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0778.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0774.jpg

[dacantu]

Phase 3- cont'd

This was after I decided that the colors in my bay were a little bit ridiculous
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0789.jpg

Freshly Painted/Restored OEM Mudflaps/Mudguards :D
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0786.jpg

Newly Painted and Reupholstered OEM armrest and console from an SE-i Accord. New head rests also installed (First pictures you can see anything related to the 5 speed swap)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0807.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0804.jpg

2/16/2010 Last day before wiring short occured and being parked for about a year
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_0793.jpg

[dacantu]

Phase 4- Out of Commission and got rid of a couple goodies :(
During its time that it was parked it also had these A-Tech Monoblock 15"x7" wheels put on just for shits n giggles (I thought they flowed well with the look of the car actually)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_1475.jpg

[dacantu]

Phase 5- Fast Forward to 1/2/2011 (Current Build)
I got the car running.
- Had lots of help with my wiring issue from a very talented Honda Tech/Electrician (LX-Incredible from 3geez.com) ***He also donated a stock exhaust manifold and stock catback (Thanks again buddy)
- I also Replaced the starter that went bad
- After these couple of things the car started right up and ran for a couple weeks no problem, thats when my clutch finally gave out on 1/24/2011.

Here's where I begin to get the motivation to start up with this project again.....

I called around to a few places to get the best deal on a clutch and clutch cable I could find and on 1/26/2011 I started putting in work. I ran into a couple problems with the light of day, and my clutch cable so finally by 1/27/2011 I was finished with the new clutch being installed, and even had the energy to give her a real nice wash. How 'bout them SI's huh? Used to hate em but on here I absolutely love em.

http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110126_143225.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110129_124134.jpg

NEW VS. USED
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110126_180341.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110129_124416.jpg

http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110126_190105.jpg

1/27/2011(Still) After the clutch install it felt just right, shifted smooth, and made me want to keep doing work. SOOOOO, I gave her a nice little wash.

Back on stock suspension
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110130_173714.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110130_173727.jpg

1/29/2011
I decided to get back to work and remove the remaining tint left on the back window. (Fishbowl FTW)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110129_194441.jpg

[dacantu]

Phase 5-cont'd


1/31/2011
Lots of work got done...
1. I Picked up a couple new headlight motors (Mine never worked properly after I had the wiring issue go wrong. So for about a year or so my headlights were permanently popped up)
-I cleaned/restored em to their original finish and voila Brand nUsed VS. the old used ones.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_195133.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_204121.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_204139.jpg

2. Did a little bit of spring cleaning (Can you spot the parts I removed?)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_204046.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_204030.jpg

3. Installed a NRG Quick Release Steering wheel setup that I got in a trade. The setup came with a NRG V2.0 Short Hub from a 94-2001 Integra, a NRG Gunmetal quick release, and a cheap eBay Steering wheel. (I got a hell of a deal in the trade) ***Still needs a little bit of tweeking but its on and functional. Im going to have to look into swapping in a different steering column possibly for a little bit better fitment.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_210602.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_210620.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_211126.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_211554.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_212741.jpg

[dacantu]

Phase 5-cont'd x2
2/1/2011:
Went to Checker/O'Reilly and picked up 5 feet of new 3/8" P/S lines and a box of clamps. Grabbed a clutch master cylinder from a DC Integra out of my parts pile and went to work on my P/S delete reservoir (this reservoir and bracket are temporary until I find something a little bit more appropriate) I am more than likely going to pick up the same bracket and reservoir that (JFern) picked up for his P/S delete, he is who inspired this simple mod.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110201_192937.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110201_192945.jpg

Enjoy for now boys! :bandit:
Also Update for tmw: Can you guess what these are? Yup, cut DropZone Lowering Springs on blown stock struts lol (These are VERY temporary, i just hate the monster truck look and already have new suspension in the works ;)). Theyre already put back on my car and yet again I'm pretty damn low. Pictures of the car will have to wait until tmrw when I get the car washed after this last rain/dust/wind storm that randomly came through AZ.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110201_193948.jpg

And for the very near future, Here's a little something I picked up. Some 4 door rear handles for a key hole delete, and the 2 way pager alarm with door lock actuators out of my old crashed DC Integra.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110131_222031.jpg

[forrest89sei]

Looking Good!!!!

[dacantu]

Looking Good!!!!

Thank you, I needed to get motivated again. :wave:

[Jajle]

Very nice! /subscribed
Makes me want to put work into my SE-i and get it running again.

[ShyBoyCA6]

Looks good and keep it up Dan. Finally to see a Black coupe being Worked on and cared for :) i dont see that on here and giving me more motivation to finish mine :D. Black Coupes Rule!!!:beer::tongue:

[poison2003]

very cool i like it

[dacantu]

Very nice! /subscribed
Makes me want to put work into my SE-i and get it running again.
What are you waiting for?


Looks good and keep it up Dan. Finally to see a Black coupe being Worked on and cared for :) i dont see that on here and giving me more motivation to finish mine :D. Black Coupes Rule!!!
Thanks Mark :D I'm hoping nothing gets in the way this time. I hate neglecting my accord ever.


very cool i like it
Thank you, stay tuned.....

[Jajle]

What are you waiting for?


It's practically totaled. I may see what I can do though, I love the car way to much to see it's progress come to an end.

Btw, the Si's are SEX, can't wait for pics of the Jerry-rigged suspension. :P

[MessyHonda]

you have a nice looking car

[dacantu]

It's practically totaled. I may see what I can do though, I love the car way to much to see it's progress come to an end.

Btw, the Si's are SEX, can't wait for pics of the Jerry-rigged suspension. :P
Eeeh I dont know about the jerry rigged susp, its very bouncy. I hate how it rides but I absolutely love being LOW, all my cars have always been lowered to the point where I'm used to bottoming out. Hopefully sooner than later if things go as planned I will be purchasing BRAND NEW quality susp, and because this particular Manufacturer is local to me I might be able to get it much sooner than having it shipped. :bandit:

Sorry to hear about your SE-i though. I know what its like to have a practically totaled car and not have the will to let it go. I recently sent that one vehicle I was proud of (a DC Integra) to the Scrap Metal yard completely stripped. I know the feeling


you have a nice looking car

Thanks Jesse. Hows yours coming along?

[stat1K]

cars gay. :)

[-$MOKIN-]

Sweet ....LOL How many sets of rims do you have ?

[dacantu]

cars gay. :)
lol I know huh


Sweet ....LOL How many sets of rims do you have ?
just 3. 2 of which are not pictured. Everything pictured besides the SI's are no longer in my possession.

[Hondamonster]

i really didn't hate the bay with the red valve cover. interested to see what you do with it! and just so you know, pull the drivers side fender and stuff that huge wiring loom way up high so your tires don't hit it. i've burned through it in places. and not to mention the hood release cable...

[Pico]

the car is looking good, glad to see you getting back into it

[2drSE-i]

aaaand subscribed.

[RobT5580]

Looks good i need some motivation as i have been lacking. Good luck?

[dacantu]

i really didn't hate the bay with the red valve cover. interested to see what you do with it! and just so you know, pull the drivers side fender and stuff that huge wiring loom way up high so your tires don't hit it. i've burned through it in places. and not to mention the hood release cable...
I wasn't feeling the red at the time.

Yeah I've got the wiring loom issue worked out. I machined some brackets that hold the harness up as high as it goes in the fender well without coming close to the tire.


the car is looking good, glad to see you getting back into it
Thanks Pico :) I'm glad to be working on her again and excited to see the finished product.


aaaand subscribed.
Lol thanks 2dr :D


Looks good i need some motivation as i have been lacking. Good luck?
When you look at you car does it upset you that you its not at the point you want it to be? That should be more than enough motivation ;)

[dacantu]

Here's a pic I took of it today boys
I didn't have a chance to wash her up but I made sure to take a picture for y'all

Enjoy guys.
http://i679.photobucket.com/albums/vv153/dacantu/IMG_20110203_151000.jpg

[forrest89sei]

I love the wheels, Those are one of my fav OEM Honda Wheels

[stat1K]

wicked curb dent under driver door?

[RobT5580]

When you look at you car does it upset you that you its not at the point you want it to be? That should be more than enough motivation ;)

Yeah lately its been more over whelming because i want to strip the car for paint but don't know how far i will get by spring. I use to feel more motivated when this site had a lot going on. Now i lurk around and it is very slow going here but thats the nature of building a older car and taking so long to build it.

[dacantu]

I love the wheels, Those are one of my fav OEM Honda Wheels
GSR Blades are my gave OEM 4x100 wheel by far. THE HFP factory whhels are so nice too :D


wicked curb dent under driver door?
no man that was just me having a bad day. That became a jack point to lift the car on to a tow dolly. (Facepalm)


Yxeah lately its been more over whelming because i want to strip the car for paint but don't know how far i will get by spring. I use to feel more motivated when this site had a lot geoing on. Now i lurk around and it is very slow going here but thats the nature of building a older car and taking so long to build it.

Maybe if you hearthat I completely stripped every single removable part/screw off of my Acura integra carefully without breaking anything (besides glass lol) in 2 afternoons you might be a little more motivated to start soon. But I agree the fact that this site is so slow moving is what got me to stop logging. In for periods of time. But seeing my car not being showed the love she deserves is what really goreally got me going again.

[dacantu]

UPDATE 2/8/2011
:D
1. Finally got around to doing a little bit of cleaning on the bay after the PS/AC/CC delete. I had cleaned my bay a few times before, so this time I just took it down to the Self Service car wash, sprayed it with some (LA's Totally Awesome Grill and Stove Degreaser,) let it sit for a few minutes and let the pressure washer do the rest. NOTE! If you do this be very careful not to get water in your intake, let the engine cool or you could warp different parts if not completely F your engine, and cover distributor.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110205_141431.jpg

Here's a close up of the PS delete reservoir. (You can see my ghetto rigged hood prop, I've gotta pick up OEM hardware for that soon, It looks so shitty)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110205_141445.jpg

2. I also picked up some Brand Newsed H, Accord, and Trim Level emblems. I was stupid a long time ago when I removed the emblems (face palm) I have to scavenge through my stockpile of parts and find the Original HONDA and DICK POE HONDA Dealer emblems and reattach those. Here's wha the emblems look like after a bit of polishing.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110205_142335.jpg

And here she is after a quick wash, nothing crazy.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110204_182338.jpg

[Dr_Snooz]

Car looks excellent! Very nice.

[Rendon LX-i]

Looking good man. I see you have came back. lol.

[gp02a0083]

very nice

[dacantu]

Car looks excellent! Very nice.


Looking good man. I see you have came back. lol.


very nice

Thanks guys :)

Should be getting some work done today, ill make sure to post pics guys..

[kentwat]

Glad to see it back on the road. I like all of the sets of wheels you had on it. I need new tires but I really liked how it road on 14" steels but they went with my Acura sale. I've been thinking of going to pick these up.
http://bham.craigslist.org/pts/2185524056.html

[dacantu]

Glad to see it back on the road. I like all of the sets of wheels you had on it. I need new tires but I really liked how it road on 14" steels but they went with my Acura sale. I've been thinking of going to pick these up.
http://bham.craigslist.org/pts/2185524056.html

Do it. I also had circuit 10s on at one point which I traded for those ATech Monoblocks. They definitely look good if the car is lowered :)

[dacantu]

Working on a small update for tonight guys :) check in later today! You won't be disappointed.

[import racer]

Looking good man,wish it was warmer here so i could work on mine.

[dacantu]

BIG UPDATE 2/16/2011

So I've been doing a little bit of work in my free time :D
I figured since I had tons of parts from my wrecked Integra I'd go ahead and custom fit most of the suspension to the Accord in order to increase my options for aftermarket parts. So I went ahead and picked up some stock accord parts to make taking measurements tons easier than attempting to take measurements while the parts were on the car. Picked up all of this for the low price of $50 bucks
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110209_174155.jpg

Here are the Integra parts I removed from my wrecked DC and that I will be using to adapt to the Accords chassis. I also sawzalled (I know its not pretty but I left lots of room to work with later) the Integra rear subframe out of the car, now I have to find a way make this fit the accord which really shouldnt be hard but will require me to cut part of the accord :( After modifying and installing the rear subframe I plan on going with either an ASR or Function 7 rear subframe brace, with function 7 Lower Control Arms and an ASR rear sway bar!
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110209_182502.jpg

This past weekend I ran into a problem with the Fuel IN line. I was on my way home when it happened, so I attempted to ghetto rig it in order to make it the extra 3 mile trip home. 3 miles later the fuel leak went from a small squirt to a huge leak and I lost more than 1/4 tank of gas.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110211_130826.jpg

So on Sunday 2/13/2011 I made a trip to the JY and picked up a Brand Nused Fuel Line (I couldnt let myself pay $70+ on the Honda Parts websites) After getting home I cleaned up the JY line a bit with some AWESOME Degreaser and a Scotch Brite pad. Here is a pic of the old and new line after cleaning it up.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_182055.jpg

While at the JY I didnt let myself leave without checking the interior,trunk,engine bay, and suspension of each and every 3gee in the yard (atleast 30 to 35 3geez). Low and behold after checking just about each and everyone and down to the last few I decide to open the door to a 3gee that I was literally about to skip and look at what I find. Original 1989 owners manual, Original 1989 Warranty Book, Cruise Control Instructions, and an AM/FM/Cassette Player Instructions Manual. Can you say JY Score!!!!?
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_165835.jpg

I also found an Armrest in an LX-i along with cupholders that were trash. I left the cupholder there and picked up the Armrest even though I dont need it. Its going in the stock pile.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_165431.jpg

[dacantu]

BIG UPDATE 2/16/2011 CONT'D

I also picked up a couple sets of used NGK wires from the JY for $0 since I cant manage to find my old set. Heres what they looked like when I got home
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_173733.jpg

What they looked like after about 10 minutes of elbow grease.http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_173650.jpg

Here's the bay with the old (practically new with only like 750 miles) plugs.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_173751.jpg

Here are the NGK installed. So pretty!!!!
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_174527.jpg

After the last 4 years of searching for one of these prop rod clips at the JY I FINALLY found one!
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_165625.jpg

Prop rod before. Protected with the insulation from hitting the positive post on the battery (which had already happened once before and it wasnt pretty)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_170843.jpg

After installing the clip. Ahh I can now rest easy knowing my prop rod is secure!
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_170902.jpg

I also managed to finally find a set of Hatch mouldings that werent all beat up or bent. These are not in the best of shape finish wise but I do plan on cleaning them up a little, and refinishing them with SEM Trim Paint.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110213_165447.jpg

Enjoy the update guys!!!!

[dacantu]

Damn no love huh. Wait until the B20VTEC swap, shaving of the bay, and wire tuck are in the works and this thread will be on fiya :D

[charliekuney]

Good thing you bumped it for me. I don't know why I missed it yesterday. I want to see that trim on and 289347502938570 pictures of it! What did you use to get the black off of the head gasket cover?

[dacantu]

Good thing you bumped it for me. I don't know why I missed it yesterday. I want to see that trim on and 289347502938570 pictures of it! What did you use to get the black off of the head gasket cover?

Wait do you mean the black wrinkle plate on the valve cover? I just used aircraft remover or paint remover from a spray can. You can get it at auto zone or checker o' reilly.

And thanks Charlie ill be working on the side moldings today man. Pics will be up either today or tomorrow.

[dacantu]

Tomorrow there will be an update :D

[Rendon LX-i]

Nice work bro. I don't get no love either lol not like I used to. I post something or update my thread it's like I'm not here only the few people on here I know sY something lol.

Nice update doing work carnal . I'll be doing a pretty big update to. Looking good thou

[Tdurr]

damnn son. i havent seen this thread in ages. Looking good man. I wish my bay was that clean, but once pollen season is over then it will be purdy again haha

with ur ps delete what does that mini reservoir go to? im interested in it..

[Rendon LX-i]

Jfern did it and i was the 2nd that did it now he did. Not that hard man. ill find the link for you.

K just like that LOL http://www.3geez.com/forum/showpost.php?p=962261&postcount=29

[Rendon LX-i]

I used a civic clutch resevior. instead of that big ass thing he used

[dacantu]

Nice work bro. I don't get no love either lol not like I used to. I post something or update my thread it's like I'm not here only the few people on here I know sY something lol.

Nice update doing work carnal . I'll be doing a pretty big update to. Looking good thou
Lol yeah man this forum is DEAD!


damnn son. i havent seen this thread in ages. Looking good man. I wish my bay was that clean, but once pollen season is over then it will be purdy again haha

with ur ps delete what does that mini reservoir go to? im interested in it..
yeah man this is my new official thread. I love how my bay is looking but it is still in for a makeover. And I used a Integra hydraulic clutch master cylinder/reservoir.


Jfern did it and i was the 2nd that did it now he did. Not that hard man. ill find the link for you.

K just like that LOL http://www.3geez.com/forum/showpost.php?p=962261&postcount=29
And I was the third to do it :D


I used a civic clutch resevior. instead of that big ass thing he used
Does it look anything like the integra one?

[elpuma]

Nice work man! I'm really diggin your build. Cant wait til i see your wire tuck. I've done mine on the drivers side and its really easy. Still have to do the passenger side. Keep up the good work though

[bullard123]

Nice work man!!! I really like that first set of rims you had on it. Looking very clean now

[dacantu]

Nice work man! I'm really diggin your build. Cant wait til i see your wire tuck. I've done mine on the drivers side and its really easy. Still have to do the passenger side. Keep up the good work though
Thanks man. The wire tuck wont begin for a few months. But I will definitely be putting in lots of work in different ways so stay tuned.


Nice work man!!! I really like that first set of rims you had on it. Looking very clean now

Yes I miss those wheels most definitely but they were damaged in my accident with my integra so I got rid of them for pretty cheap..

Working on thee post for my update right now guys :)

[dacantu]

Update 2/19/2011

So two nights ago I put in some work on the moldings I pulled off a hatch at the yard, i've just been too lazy to update.

After sanding them down
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110217_200155.jpg

This is how the car sat without molding probably for 2 years now.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110203_173055.jpg

And after painting them with Trim Paint this is the outcome, there are still a few minor imperfections but I'm satisfied for now. I will be looking to buy some brand new ones along with brand new bumper covers when I get my car painted. They fit just like the stock coupe molding do but look 1,000,000x better!
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110218_125053.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110218_125128.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110218_125108.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110218_125150.jpg

Enjoy...:thumbup:

[Pico]

Sweet, I'm loving youre build thread, it gives me a reason to keep on with my Accord
Keep up the great work

[dacantu]

Sweet, I'm loving youre build thread, it gives me a reason to keep on with my Accord
Keep up the great work

Thanks pico, dont stop loving your accord. BTW I'm liking how your car looks in your sig man.

[Hazwan]

Thanks pico, dont stop loving your accord. BTW I'm liking how your car looks in your sig man.

X2 and trims are looking real good man :thumbup:

[Salo_89_Accord]

Looooking good dude....and also suuuubscribed
can't wait to see what comes next :nervous:

[phrenology]

Trim lookin' so fresh and so clean!!!

[Pico]

Thanks pico, dont stop loving your accord. BTW I'm liking how your car looks in your sig man.

Thanks Bro.

[dacantu]

X2 and trims are looking real good man :thumbup:
Thanks buddy. Hows the carputer working out?

Looooking good dude....and also suuuubscribed
can't wait to see what comes next :nervous:
Whatever it is you won't be disappointed :D


Trim lookin' so fresh and so clean!!!
Thanks mane. Stop by often.


Thanks Bro.
No problem man.

[dacantu]

Update 2/23/2011

New look for my 3gee. Traded my SI's for some Work Replicas (DR20's) and kept my pretty much NEW tires. SCORE!

At the tire shop
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_140144.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_135426.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_140114.jpg

On the way home
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_151303.jpg

Bubble Bath (The wheels were looked like they hadnt been cleaned since new so I had to do some major cleaning)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_171156.jpg

The results...
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_181046.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_180510.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_181023-1.jpg



Enjoi :D

[ShyBoyCA6]

Should of sold me the si rims W/tires. Looks good man! Gonna work on my coupe tomorrow been a couple weeks since my sedan left me for dead and didn't have time to work on it.

[cubert]

looks muuuuch much better with the new rims (not that it looked bad before, just better now) :thumbup:

[Ayeobe]

As im sure the entire world knows, i love me some black rims... therefore, you have my aproval LoL sick shit, man, keep it up.

[Rendon LX-i]

Hotness

[Pico]

I think I just wet myself :D

[mushroom_toy]

Looks great man!

[Rendon LX-i]

i had to come say WOW. just one more time LOL

[-$MOKIN-]

Lovin it . Hey did u scrape the paint off of the rear window trim ? I did that too i like the chrome on it. Looks sweet the fronts got some Camber going on doesn't it? Hows the tire wear ?

[dacantu]

Should of sold me the si rims W/tires. Looks good man! Gonna work on my coupe tomorrow been a couple weeks since my sedan left me for dead and didn't have time to work on it.
Lol SI's are a dime a dozen. I'm sure you can find a minty set near you for cheap.


looks muuuuch much better with the new rims (not that it looked bad before, just better now) :thumbup:
lol thank you. By far my favorite set of wheels I've had on the accord so far. They accent it perfectly.


As im sure the entire world knows, i love me some black rims... therefore, you have my aproval LoL sick shit, man, keep it up.
Thank you and will do ;)


Hotness
Gracias hermano.


I think I just wet myself :D
lol thanks Pico, keep tuning in man.


Looks great man!
Thank you. I'm liking yours in your sig also man.

i had to come say WOW. just one more time LOL
Lol :D


Lovin it . Hey did u scrape the paint off of the rear window trim ? I did that too i like the chrome on it. Looks sweet the fronts got some Camber going on doesn't it? Hows the tire wear ?
The tire wear is pretty bad but these are new tires so im not too worried about it right now. And yeah actually the trim was peeling from the sun so injustice took a razor blade to it and made it look as nice as I could. I will be buying new trim when I paint it. For an extra fresh look

[86AccordLxi]

Wait, teggy rear susp just to run some bling control arms?

It's all double wishbone anyway, isn't it? Why would you even bother?

[MessyHonda]

haha...that one low coupe

[dacantu]

Wait, teggy rear susp just to run some bling control arms?

It's all double wishbone anyway, isn't it? Why would you even bother?

Yes Integras are double wishbone type suspension. The point isnt to just run some nice control arms. Its so that I can expand my options for better quality parts. It gives me room to mess around with and tweak my suspension. Who knows, in the end it might not be worth the trouble but it cant hurt to try it.


haha...that one low coupe

Thanks Jesse. I think for functionality I might be raising it in the near future. It wont be a whole lot but just enough to ride comfortably, fit some nice wheels, to accomplish a nice stance, and also for fitment of whats coming next :D

[dacantu]

Update 3/1/2011

So yesterday 2/28/2011 I picked up my new GSR Head.

Details on the head: Ported and polished, 3 angle valve job, supertech dual valve springs, JDM GSR cams with a polished port matched ITR intake manifold.

I will be on the lookout for a JDM B20 Block (not JDM B20A) and will hopefully be starting my CR-VTEC/B20VTEC swap sooner than anticipated. The head will be cleaned, checked for warpage, inspected for quality of said work done, and I will more than likely do out with the entire valve train as well as the cams and cam gears. All in all the head will be brand new before it is ever mounted on a block.

Here she is guys
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110228_161210.jpg

Enjoi :D

[dacantu]

Swap Main Checklists. (More will be added and updated as I acquire more parts)

B Swap Main Checklist. In Process of Completing
[x] DOHC VTEC Head (GS-R)
[x] Shift Linkage
[x] Mount Brackets

OBD1 Main Checklist. In Process of Completing
[x] ECU
[x] Distributor
[x] OBD1 ECU Pigtails

[Dr_Snooz]

GSR head FTW! You have lots of work ahead of you yet. Looks great so far.

[-$MOKIN-]

Are u putting that on a A20 and how ?

You rock dude......I love it man keep up the work bro . You doing great

[Pico]

:bow: :bow: :bow:

[stat1K]

Are u putting that on a A20 and how ?

You rock dude......I love it man keep up the work bro . You doing great

man reading is hard.

[ShyBoyCA6]

Are u putting that on a A20 and how ?

Bro...he is gonna use the B18 gsr head with a jdmB20 block from a cr-v. No way this will fit on the A20 block

Not to be an ass but you should read up on what he post :D



And daniel good luck on the swap bro! This thing is gonna scream Vtakk (if you decide to use vtec).

[-$MOKIN-]

OOpps hahahah im a retard and i know it ....Well thats sweet man...Its going to be a beast

[dacantu]

GSR head FTW! You have lots of work ahead of you yet. Looks great so far.
I'm truely looking forward to it. I wish I had a welder though. It would cut costs of this build greatly with what is in store.


Are u putting that on a A20 and how ?

You rock dude......I love it man keep up the work bro . You doing great
Yeah dude gotta read man. There is no head that will bolt to the A20 block. But thanks man keep dropping in for more updates.


:bow: :bow: :bow:
:wave:


man reading is hard.
lol


Bro...he is gonna use the B18 gsr head with a jdmB20 block from a cr-v. No way this will fit on the A20 block

Not to be an ass but you should read up on what he post :D



And daniel good luck on the swap bro! This thing is gonna scream Vtakk (if you decide to use vtec).
Be easy Mark, no need for the hostility mane lol. And yes of course I will has teh vtacs wired up mane. No point in running a vtec head otherwise. Thanks though man, I'm looking forward to more income so I can speed up this build also.


OOpps hahahah im a retard and i know it ....Well thats sweet man...Its going to be a beast
That's what I'm aiming for. K swap killa hopefully.

[ShyBoyCA6]

I call shot gun when its done :D lol

[charliekuney]

http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/Danny085.jpg


http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110222_180510.jpg

I'm very much loving (grammatical error) the changes, 'cept the front bumper. ;)

Next for dacantu:
sedan rear handles/power locks
painted window trim

[MessyHonda]

oh yeah that motor is going to kick ass

[mkymonkey]

damn son, that thing youre buying from me will look legit in here ;)

I'm glad its going on a coupe too

[dacantu]

I'm very much loving (grammatical error) the changes, 'cept the front bumper. ;)

Next for dacantu:
sedan rear handles/power locks
painted window trim
Dude I've got the rear handles and actuators already. They're just not installed yet because of the actuators not fitting right. Soon enough.


oh yeah that motor is going to kick ass
Its going to be a beast!


damn son, that thing youre buying from me will look legit in here ;)

I'm glad its going on a coupe too
I'm doing my part to keep the few coupes out there alive lol. And yeah man those parts should look killer. I'm looking forward to getting those fromyou in the mail soon :)

[Ayeobe]

I'm lovin your front bumper man, wish i could have one =p Finding one up where i live is nearly an impossibility.. Do the sedan rear bumpers fit on the coupe? I love the rear bumper on the sedan for the pre-facelift. Looks way smoother and such.

[dacantu]

I'm lovin your front bumper man, wish i could have one =p Finding one up where i live is nearly an impossibility.. Do the sedan rear bumpers fit on the coupe? I love the rear bumper on the sedan for the pre-facelift. Looks way smoother and such.

I'm not so sure on the rear bumpers being interchangeable. I've never looked at them well enough to compare. I'm going to have to try it one day that I'm at the junkyard.

If youre ever interesed in me sending you one of those bumpers I'm more than willing. You would have to pay the cost of the bumper plus shipping but if youre really that interested there is a mint condition one at a junkyard near my home.

[dacantu]

UPDATE 3/13/2011

So I got some small things done over the last week. I began to install the stock exhaust that Angus donated to me over the summer. I was so tired of the ricer ass exhaust that I installed a couple years back (what a waste of funds)

I was planning on installing it after giving it a rinse with the water hose but it wasnt convincing enough for me. I thought it would take away from the overall appearance of the car. So I went ahead and applied a small amount of the good old elbow grease. :D

Before
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110305_150147.jpg

After
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110305_143526.jpg

I also managed to find and polish up a stock Chrome Tip and added that to the end. Makes a huge difference in my opinion.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110305_150225.jpg

In with the new, out with the old
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110305_151251.jpg

And on the ground, I plan on taking it to an exhaust shop to have the hooks relocated to tuck it up against the bumper a little more. (Also in this pic you can get a teaser of the new car)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_174455-1.jpg

[ShyBoyCA6]

nice and i see you got a hatch.

[dacantu]

Update 3/13/2011 CONT'D

This one here is for Rendon :D

I remembered Rendon posting a thread on these visors, so I went ahead and mocked it up on the rear window of my coupe. It fir with absolutely no modification and actually follows the lines of the car (where the window ends and the roof begins.)

Before mocking it up to the car I thought it would just be for the sake of research lol but after seeing it mounted I decided I actually liked how it looks. The color of my car i think flows well with the visor. I'm going to go ahead and keep it on there for a while and decide whether it'll stay or not although before I put it on I thought they looked horrible on just about any other car lol
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_161225.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_165107.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_174426.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_161337.jpg


Enjoi :D

[stat1K]

diggin it,

i would have just had a better muffler welded on the aftermarket exhaust instead of the fart can.

i wonder if that's the exhaust off of my coupe? lol...

[mkymonkey]

that piping on the ricer exhaust looks quite good...2.5"?

I would totally try putting on a different muffler on there, or sell the piping make some extra change :)

[dacantu]

nice and i see you got a hatch.
Thanks mane. And nope not a Hatchy. Its a coupe, the reflection is distorted.

diggin it,

i would have just had a better muffler welded on the aftermarket exhaust instead of the fart can.

i wonder if that's the exhaust off of my coupe? lol...
Thanks Pat.
I will be having a better muffler (RS*R) welded on to 2.25" piping once the swap is finished. But 2.5" was just a little over the top.

I'm not sure if its your old piping but its mine now lol :P

[ShyBoyCA6]

Thanks mane. And nope not a Hatchy. Its a coupe, the reflection is distorted.

Thanks Pat.
I will be having a better muffler (RS*R) welded on to 2.25" piping once the swap is finished. But 2.5" was just a little over the top.

I'm not sure if its your old piping but its mine now lol :P

another coupe...in white?:jaw:

no chinges congrats bro! same year or older?

and dont let her be camera shy! post some pics daniel lol

[dacantu]

that piping on the ricer exhaust looks quite good...2.5"?

I would totally try putting on a different muffler on there, or sell the piping make some extra change :)
Yeah it is 2.5" and in great condition man, the only problem is that it is one whole piece and shipping would be stupidly priced. It really not worth it to me to sell unless someone local bought it. I'm thinking of picking up an RS*R axleback exhaust and throwing it on 2.25" piping once I swap the B in there.

Were you able to pull off those parts this weekend?


another coupe...in white?:jaw:

no chinges congrats bro! same year or older?

and dont let her be camera shy! post some pics daniel lol

Lol yeah its an '89 LX-i in white with minty maroon interior. It has a auto trans thats trashed, but the car starts up and runs like a dream. Has brand new tires, and brand new Pioneer stereo and speakers. Paid $500 for it. Pics coming up, i'll post a link.

[dacantu]

If you want to see pics of the new coupe click HERE (http://www.3geez.com/forum/showthread.php?p=1057019#post1057019)

Enjoi :D

[stat1K]

you're building an army, now between you an angus you guys have 6?

well angus has 3 really and his sister has a white coupe just like that. lol... more running 3geez than half this site.

[mkymonkey]

Yeah it is 2.5" and in great condition man, the only problem is that it is one whole piece and shipping would be stupidly priced. It really not worth it to me to sell unless someone local bought it. I'm thinking of picking up an RS*R axleback exhaust and throwing it on 2.25" piping once I swap the B in there.

Were you able to pull off those parts this weekend?


negative sir...I couldnt get over there BUT I'll try to go there in a few hours on my lunch break. anyway...peep my rs*r

http://i92.photobucket.com/albums/l10/mkymonkey/FLUC/2fc5547e.jpg

http://i92.photobucket.com/albums/l10/mkymonkey/FLUC/c19ff9c9.jpg

[dacantu]

I've got a few updates for this thread sometime today or tomorrow

[dacantu]

you're building an army, now between you an angus you guys have 6?

well angus has 3 really and his sister has a white coupe just like that. lol... more running 3geez than half this site.
lol well it seems that Arizona is the home of nice clean restorable coupes where 4doors and hatchies are unwanted! Lol


negative sir...I couldnt get over there BUT I'll try to go there in a few hours on my lunch break. anyway...peep my rs*r


RS*R makes a great sounding exhaust. I hope having to modify one for my accord won't change that drastically if at all which I'm sure it will.

[Questionable?]

tasteful. thats how you do it.

[mkymonkey]

just get the right piping and the right welder and you might just pull it off :)

[Rendon LX-i]

Update 3/13/2011 CONT'D

This one here is for Rendon :D

I remembered Rendon posting a thread on these visors, so I went ahead and mocked it up on the rear window of my coupe. It fir with absolutely no modification and actually follows the lines of the car (where the window ends and the roof begins.)

Before mocking it up to the car I thought it would just be for the sake of research lol but after seeing it mounted I decided I actually liked how it looks. The color of my car i think flows well with the visor. I'm going to go ahead and keep it on there for a while and decide whether it'll stay or not although before I put it on I thought they looked horrible on just about any other car lol
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_161225.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_165107.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_174426.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110312_161337.jpg


Enjoi :D

Asshole lol. My bad I haven't been on much. But u have a coupe so idk if the windows are the same? Looks sexy bro. I yet have to get the visors from Aaron .

[ShyBoyCA6]

Update??:wave:

[stat1K]

he's too busy polishing knobs.

[knarg]

awesome build and good progress pics.

[HERBERT]

What is that visor from!!!!!!!!!!!!!!

[dacantu]

Okay update on its way (uploading and resizing pics) as I type this message.


tasteful. thats how you do it.
Thank you senor.


just get the right piping and the right welder and you might just pull it off :)
I have recently met a fabricator that ive been wanting to meet so I dont think thhis will be an issue ;)


Update??:wave:
On its way broskie


he's too busy polishing knobs.
lol pinche patricio mamon. lol love ya man no homo


awesome build and good progress pics.
thanks man, glad the OG's can stop by and give props.

[Tdurr]

pics nao!!!

[Rendon LX-i]

A mas puto LOL. you didnt even reply to my shit. ORALE GUEY i see how it is. MUUUY CHINGO to reply back. LOL what car you get that rear visor from? i dont think it would matter sedan windows are a bit more curvy at the ends.

If you dont mind CHeck how it fits on a sedan bro

[bullard123]

What is that visor from!!!!!!!!!!!!!!

Yeah that visor is hot bro and I know it will fit a hatch....Lol come on man stop holding out:kekeke:

[Pico]

Yeah that visor is hot bro and I know it will fit a hatch....Lol come on man stop holding out:kekeke:
Agree I need to get one for my hatch also

[HERBERT]

gahh i check this like 20 times a day just cuz i wanna no

[mkymonkey]

Didn't he say it was from his girlfriends teggy?

[stat1K]

Didn't he say it was from his BOYFRIENDs teggy?

fixed*

[dacantu]

Asshole lol. My bad I haven't been on much. But u have a coupe so idk if the windows are the same? Looks sexy bro. I yet have to get the visors from Aaron .
I'm not sure if the windows are the same bro. I think the four doors are alot steeper drop in the rear window where the coupes aren't as steep


pics nao!!!
Yes sir.


A mas puto LOL. you didnt even reply to my shit. ORALE GUEY i see how it is. MUUUY CHINGO to reply back. LOL what car you get that rear visor from? i dont think it would matter sedan windows are a bit more curvy at the ends.

If you dont mind CHeck how it fits on a sedan bro
Lol my bad bro I thought I had replied. But anyway man I ddont have no way of checking it on a four door but I pulled it off of an integra but it was modified to fit the integra so I don't know what it was originally from.


Yeah that visor is hot bro and I know it will fit a hatch....Lol come on man stop holding out:kekeke:
I'm not sure, the coupes and hatches have different rear windows.


Agree I need to get one for my hatch also
do it


Didn't he say it was from his girlfriends teggy?
Pulled from an integra but not originally from an integra señor. :D


fixed*
lol

[2geetrey]

That thing looks good can't wait to see the finished product

[dacantu]

UPDATE: 4/8/2011 (MY COMPUTER TOOK A CRAP GUYS SO ALL UPDATES WILL BE DIRECTLY FROM MY PHONE, SORRY ABOUT THE PIC SIZE I CANT RESIZE FROM MY PHONE)

Here's my currently heartless coupe. I blew a headgasket and picked up a new engine for $100 bucks so just going to swap it out while I build my b20v swap.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110405_174243.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110406_150415.jpg

Here are some of my parts for the obd1 b swap. (I'm not sure whether to go with the greddy sandwhich kit or the t hose for my B20VTEC.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110328_161905.jpg

Rear bumper skirts from a 5th or 6th Gen accord
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110328_160218.jpg

My old ricer project fog lights from a prelude lol if anyone wants these lmk ill ship em for $25.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110328_160544.jpg

Here's my new foglight project. I'm keeping the original glass lenses this time I just have to replace one of the broken glass lenses with one from my old setup.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110328_160640.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110328_161709.jpg

And here's my OEM optional equalizer :)
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110328_162024.jpg

Sorry about the delay on the update guys but I hope you all enjoy the update :D

[ShyBoyCA6]

Thanks Daniel! You gave me an idea for a mod :D and should look sweet. And nice update keep it with the a motor :D

[stat1K]

get it done, it's getting too hot maing.

oh i'll be in town from may 13-23rd. i'm calling angus later to let him know when i'm coming. last time we went to f1 race factory, probably gonna do it again since we paid for the yearly membership last time in december.

on a side note, wanna buy a guitar :)

[dacantu]

Thanks Daniel! You gave me an idea for a mod :D and should look sweet. And nice update keep it with the a motor :D
Hell na out with the A20 (for now) lol n what mod is that?


get it done, it's getting too hot maing.

oh i'll be in town from may 13-23rd. i'm calling angus later to let him know when i'm coming. last time we went to f1 race factory, probably gonna do it again since we paid for the yearly membership last time in december.

on a side note, wanna buy a guitar :)

Dude its 64° here right now! Its perfect to work on my car lol. I'm dropping the engine in today after I get out of school anyhow.

I turn 21 on the 12th of this month so that's perfect bro lol. I'm down for some F1 Race, I haven't been there in about a year or so. Get ready to have your ass handed to you lol. Lets try n get some good times in this time you're here. Don't forget to save my number before you come down here.

And na man I have two guitars as it is and can't play for shit, don't need another one lol.

[stat1K]

LOL WELL hoorah son, who'da thunk it was cooler there than here. it's gonna be 82 here today.

man, we have way to many may birthdays. my wife's the second, my buddy chris is the fifth, my friend out here is the 11th, my buddy mike is the 15th, and my brother is the 30th. not to mention my fifth wedding anniversary will be may 22nd this year lol...

but yeah, this time you'll be able to drink a beer with us between races, legally!

i've got 2 and a mandolin that i just got. got a great deal on the one i'm selling so i'm trying to turn a slight profit. if you know anyone i can probably bring it to az on my flight.

[ShyBoyCA6]

Gonna add EQ at the bottom of the cup holders. Since I don't use the bottom part much. I have one laying around and should be a sweet addition :)

[Rendon LX-i]

Nice

[knarg]

I have an OEM EQ and CD!

http://farm2.static.flickr.com/1166/617843288_615674f07e_z.jpg

[Tdurr]

still lovin this car. keep up the nice work bro!

[-$MOKIN-]

I have an OEM EQ and CD!

http://farm2.static.flickr.com/1166/617843288_615674f07e_z.jpg

Thats nice what did this come out of?

[ShyBoyCA6]

Thats nice what did this come out of?

lol smoking you make laugh sometimes read the sentence that he put

[knarg]

Thats nice what did this come out of?

One of those crappy flip-up headlight Accords I think.

[cyndrom]

Omg, i adore your HONDA rims that are on the first page. Can you say me the code?

You are lucky that you´ve got this car :)

[RAZR]

One of those crappy flip-up headlight Accords I think.

:lol: :lol: :lol:

[AccordEpicenter]

i really love this car. Am I the only one that thinks those Si wheels looked the best?

[charliekuney]

Thats nice what did this come out of?

Factory/Dealer option for SE-i's.

[ShyBoyCA6]

i really love this car. Am I the only one that thinks those Si wheels looked the best?

Nope i think they looked great on there.

[dacantu]

Finished putting my engine in like 3 days ago, just didnt have a chance to update the thread. It is still not running because I will be waiting top buy new axle seals at the dif, new oil pan gasket, oil, oil filter, valve cover gasket, water pump, alternator belt, coolant, thermostat, and all new coolant small and large hoses.

Heres how she sits
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110410_171335.jpg


LOL WELL hoorah son, who'da thunk it was cooler there than here. it's gonna be 82 here today.

man, we have way to many may birthdays. my wife's the second, my buddy chris is the fifth, my friend out here is the 11th, my buddy mike is the 15th, and my brother is the 30th. not to mention my fifth wedding anniversary will be may 22nd this year lol...

but yeah, this time you'll be able to drink a beer with us between races, legally!

i've got 2 and a mandolin that i just got. got a great deal on the one i'm selling so i'm trying to turn a slight profit. if you know anyone i can probably bring it to az on my flight.

I dont really know anyone who plays to be honest man. And I am now officially legal to drink as of this past tuesday :)

looking forward to your trip out here man. We're definitely going junkyarding so bring your sunscreen whitey I dont want your skin to chap lol


Gonna add EQ at the bottom of the cup holders. Since I don't use the bottom part much. I have one laying around and should be a sweet addition :)
good idea but anytime the cupholder is open and you have a drink in it you will not be able to adjust the eq or the stereo lol


Nice
thanks ese lol


I have an OEM EQ and CD!

I will one day find a OEM CD player, one day


still lovin this car. keep up the nice work bro!
thanks man check out my next update.


Omg, i adore your HONDA rims that are on the first page. Can you say me the code?

You are lucky that you´ve got this car :)

which ones? quote the picture and I'll let you know. Lucky? not so much, its been nothing but problems its entire life but I do love it.


i really love this car. Am I the only one that thinks those Si wheels looked the best?
I wont lie, I miss them as well and you will more than likely see them on the car again pretty soon unless I can find some GSR blades


Nope i think they looked great on there.
Thanks doggy

[dacantu]

UPDATE 4/14/2011

I recieved a package in the mail today :omg:


Lets play teaser:
Can you guess whats in the box?
-Let me give you a hint. (It is minty OEM greatness!!!)

I will reveal what is in the box after 5 guesses from 5 different members :Owned2:

http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110414_162219.jpg

[Tdurr]

oem... uhhh... sun visors?
or.... mudflaps?

[Ayeobe]

lol REAR mudflaps for COUPES?

[dacantu]

oem... uhhh... sun visors?
or.... mudflaps?
l no sir.


lol REAR mudflaps for COUPES?

Both of you guys cracked me up with the mudflaps I have mudflaps on my car haha

[Pico]

Is it a ducktail spoiler folded into a very small box

[stat1K]

you can see the box weighs 12lbs... i'd say motor mounts?

edit i can't read about minty oem greatness so umm i think it's bolts :)

[2drSE-i]

Foglights?

[stat1K]

Foglights?

i'm officially changing my guess to this.

[dacantu]

That's five and you all suck at guessing! Lol.

So here's my update for 4/15/2011.

Big thanks to 89AccordCpe aka Rahim for the Minty parts and great shipping service.
Heres a link to his ad for better pics. http://www.3geez.com/forum/showthread.php?t=75318

So I sold my cupholder and picked up a practically brand new one for cheaper lol
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110414_162654.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110414_162707.jpg

I bought the original fog wiring harness and both amber and white buttons, along with the original brackets. No fogs though.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110414_162552.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110414_162813.jpg

And the originally wiring trouble shooting manual as well as the original 89 factory service manual.
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110414_163037.jpg

Enjoi guys :)

[gp02a0083]

dammit i wanted the manuals lol

[Ayeobe]

Both of you guys cracked me up with the mudflaps I have mudflaps on my car haha

Funny thing is, i dont like the mudflaps haha..

Sick stuff man. The cup holders look smooth, therefore i like them.. how acurate is that service manual? its not the shop manual is it?

[charliekuney]

Damn you! I wanted everything on that for sale thread!

[Fedor B.]

That cup holder looks awesome!

[Tdurr]

TITTIES!!!!

and my guess was just some bs to get u to talk :P

[forrest89sei]

:thumbup:

[Rendon LX-i]

damn son. looking good

[cyndrom]

http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110130_173714.jpg
http://i679.photobucket.com/albums/vv153/dacantu/1989%20Honda%20Accord%20LX-i%20Build/IMG_20110130_173727.jpg



I meant these rims. And which size are they?

[ShyBoyCA6]

I meant these rims. And which size are they?

They are 15's I believe

[stat1K]

those are 15" Si wheels from the 99-00 Si

[ShyBoyCA6]

Hey Daniel lil off topic here but what tires did you have on the SI wheels? size and name brand please

[charliekuney]

I always thought Si's were 16".

:inout:

[mkymonkey]

Keep it up maing!

[obdriver6]

I always thought Si's were 16".

:inout:

Thats what I tought too.

[Tdurr]

nope 15s. i have some on my car lol

[dacantu]

dammit i wanted the manuals lol
Let me know if theres anything you need from them


Funny thing is, i dont like the mudflaps haha..

Sick stuff man. The cup holders look smooth, therefore i like them.. how acurate is that service manual? its not the shop manual is it?
Not sure on service manuals yet, I havent had a chance to look at them. I'll let you know once I do buddy.


Damn you! I wanted everything on that for sale thread!
Sorry senor


That cup holder looks awesome!
Thank you


TITTIES!!!!

and my guess was just some bs to get u to talk :P
I figured most would be haha


:thumbup:
Gracias :D


damn son. looking good
Thanks mane. I'm trying, I'm trying


I meant these rims. And which size are they?
15" 1999-2000 Honda Civic SI rims


They are 15's I believe
Yup


those are 15" Si wheels from the 99-00 Si
x2


Hey Daniel lil off topic here but what tires did you have on the SI wheels? size and name brand please
205/50/15 Khumo Ecsta AST's


I always thought Si's were 16".

:inout:
Nope, the only factory 4x100 16" alloys Honda made were the HFP wheels for the EM2's I believe


Keep it up maing!
Gracias Adrian


nope 15s. i have some on my car lol
Noice, I love em on the accords I dont know why.

[stat1K]

there are factory 16" 4x100 HFP Fit wheels. moderately cheap from the dealer last i checked... they would look nice on the accord.

http://cgi.ebay.com/ebaymotors/GENUINE-HONDA-HFP-16-ALLOY-WHEEL-CIVIC-INTEGRA-FIT-_W0QQcmdZViewItemQQhashZitem5d2c322271QQitemZ40017 3441649QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccesso ries#ht_843wt_752

[ShyBoyCA6]

Thank you Daniel!

[dacantu]

Oh man do I have an update for next week. Just waiting for the sender to get the filunds and then they'll be on their way to my place. I'm so excited, I've been waiting to get these bad boys since I first owned my car I think. Stay tuned.


there are factory 16" 4x100 HFP Fit wheels. moderately cheap from the dealer last i checked... they would look nice on the accord.

http://cgi.ebay.com/ebaymotors/GENUINE-HONDA-HFP-16-ALLOY-WHEEL-CIVIC-INTEGRA-FIT-_W0QQcmdZViewItemQQhashZitem5d2c322271QQitemZ40017 3441649QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccesso ries#ht_843wt_752
that's right I forgot about those. Good looking wheels actually.


Thank you Daniel!
no problem man.

[ShyBoyCA6]

I think I know what they are lol.

[Mellexx]

No clue why I haven't seen this thread until now, Good to see you're back to working on it though!

[dacantu]

I think I know what they are lol.
don't spoil the surprise facker :p



No clue why I haven't seen this thread until now, Good to see you're back to working on it though!
Yeah man I'm happy too. Feel free to subscribe :)


Its back on SI's also.

[ShyBoyCA6]

:D i won't lol

[Mellexx]

Yeah man I'm happy too. Feel free to subscribe :)


Its back on SI's also.

Sweet, for sure did subscribe to this!

[RLong31]

Any updates lately?

[Doward]

First pic in the thread (well, after the sig pic) - what wheels were on your car? I like 'em ;)

[Edison Carasio]

Mmmmm so jealous.

[Lindsey453]

so where did that rear window visor come from? is it actually for a ca6 or was it for something else?

[dacantu]

Oh hai guyz!!!

So I've been away from my Accord for a very long time now. Its been stored away in the backyard for over a year or so now but the build will be coming back to life guys. Im going to try and get it back to its former glory atleast for the moment. So here's an update for the moment.

Picked up these wheels since my car is currently on steelies.
MSW 15x6.5" 4x100 Very Old Skool look to them.
http://i679.photobucket.com/albums/vv153/dacantu/100MEDIA36IMAG0555.jpg

[Rendon LX-i]

those look sexy

[Mellexx]

Not bad! I'm liking them

[obdriver6]

Car should look very nice with those wheels

[dacantu]

thanks guys gotta get some tires for em, thinking 215/50/15 or even 225/50/15 if i can fit them we'll see... also want to run some spacers so im not tucking as much and get them to sit flush with the fenders.

[oldschool3g]

Cant wait to see those wheels on;)