ebrake handle

[lostforawhile]

I finally got around to making my ebrake handle, tomorrow the boot
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/----------------------------------------------------------------002.jpg
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/----------------------------------------------------------------001.jpg
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/MobileUploads_1306370985701.png

[2oodoor]

i like that, and it reminds me of a windshield knife, looks good

[lostforawhile]

it's pretty much permanent, as it's driven on lol, better then the original thats for sure, I'm working on the boot tomorrow

[A18A]

sweet. what was that made from? I was gonna use the rubber cover for a hammer on mine but cbf cutting a hole in the end lol

[lostforawhile]

sweet. what was that made from? I was gonna use the rubber cover for a hammer on mine but cbf cutting a hole in the end lol

it's aluminum

[Dr_Snooz]

Very nice! The knurling is great.

[lostforawhile]

this is the piece that will form the base for the boot, it still needs finishing up as I was rough fitting it, this does the same thing as the bottom of the rubber boot, and fits over the steel of the handle itself, I need to make a couple of brackets to anchor it to the handle, the boot goes over the handle and the console cover isn't directly connected to it, I was going to make the leather boot myself, but a friend of mine is offering to make it for me
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/----------------------------------------------------------------.jpg

[lostforawhile]

Very nice! The knurling is great.

thats my 1901 three headed knurling tool, instead of doing it strictly by hand like I usually do, I set it up with the lowest feed speed possible and a very low RPM on the lathe, and let the machine feed it, it took about 30 minutes to do that knurl

[lostforawhile]

the tool looks like this, http://img.auctiva.com/imgdata/1/4/4/4/5/7/6/webimg/469603759_tp.jpg

[mykwikcoupe]

Looks great, wanna make me a shifter handle and the ebrake handle?

[lostforawhile]

Looks great, wanna make me a shifter handle and the ebrake handle?

I can probably make you one, can you find me a used Ebrake handle to work on? i can't take this one apart to measure anything, and it's been years since I made the button , but I can put one together with a parts piece, what are you looking for in a shifter handle?

[lostforawhile]

Ok I'm almost done with the boot, lots of tiny stitches later, I have to make the bezel for the boot, then it slides down the handle, once I put the bezel on, then I can glue the leather to the bottom plate. the plate attaches with a couple of brackets,directly to the E brake arm itself
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/picturespictures001.jpg
this is the master pattern, basically you cover it with masking tape, then split the tape with a razor blade, and lay it out on paper, anything that doesn't lay flat, gets split, this becomes your pattern for the material
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/picturespictures004.jpg
the pattern
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/picturespictures003.jpg
this is the bottom plate
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/picturespictures005.jpg

[Christofur]

Great work looks awesome

[Dr_Snooz]

http://i20.photobucket.com/albums/b205/moultriemanicmechanic/picturespictures001.jpg

This looks great! Make me a leather shifter boot?

[lostforawhile]

pardon the car being so dirty, it's a project of course, especially the center section over the ebrake, it's going to be disassembled and repainted soon, the center console is just sitting in here for now, so i can check clearance,

http://i20.photobucket.com/albums/b205/moultriemanicmechanic/IMG_1908-1.jpg

http://i20.photobucket.com/albums/b205/moultriemanicmechanic/IMG_1910.jpg

http://i20.photobucket.com/albums/b205/moultriemanicmechanic/IMG_1915-1.jpg

http://i20.photobucket.com/albums/b205/moultriemanicmechanic/IMG_1916-1.jpg
http://i20.photobucket.com/albums/b205/moultriemanicmechanic/IMG_1911.jpg

[mykwikcoupe]

I think you watched knightrider way too many times lost. Most people try eliminate all those switches. It looks like you have a switch to control another switch

[lostforawhile]

I think you watched knightrider way too many times lost. Most people try eliminate all those switches. It looks like you have a switch to control another switch

actually i need to wrap the center section with the mirror switch, that lets me control most of the radio functions with one finger, everything is functional and serves a purpose, it controls an swi-x unit, that duplicates the radio remote functions, the green switches will be replaced with black ones, one is radio mute, and one is function

[mykwikcoupe]

and whats the hot water knob for in the arm restr area? I have that ebrake handle

[lostforawhile]

and whats the hot water knob for in the arm restr area? I have that ebrake handle

subwoofer level

[lostforawhile]

oh the phone is going back to my museum, it just takes up too much space