obd1 code 17 (if your obd1)

[Rendon LX-i]

k will i finally got my code 17 to go away with the resistor mod on my 86 cluster. problem is that it comes back up after i slow down.

Could i just swap the pluser on the 89 cluster to the 86 or it wouldnt work?

let me know guys

[elpuma]

I say give it a try. I don't see why it wouldn't work.

[Rendon LX-i]

i have a 88-89 cluster but i fucked it up trying to do the led mod LOL but i have the parts still

[elpuma]

Yea i was thinking why not just replace the cluster with an 88-89 one. But try swapping the pulser and see if it works.

[Rendon LX-i]

http://i728.photobucket.com/albums/ww290/Rendonlxi/B1DCBCCD-73C1-4289-8BCB-1CD84B3527B6-6013-000005617F0F89A2_zpsf1e0c277.jpg

Sliced to Blk/y then stacked 4 1.5k to make 6k then To (yellow) vss output to Ecu . I have cruise connected still but not working so I did not add the diode. Like I said it works for a bit then it turns on. Does this look right to you guys.

[Rendon LX-i]

well i guess no one wants to help.

Going to put a cb7 speedo retro and get a electric vss and wire it in. simple

Going to try the 88-89 cluster first see what happens.

[2ndGenGuy]

I don't know if anybody knows how to help. From the sound of it, just about everybody with the B-series swap has a VSS code. I wish I could help ya man. Personally, I'd just run the 4g speed sensor and call it good. Ditch that crappy speeodmeter cable.

[A18A]

id reply to your PM but the PM box is full now lol. anyways, it's easier to use the CD speedo than the CB as the trip meter & odometer are in the speedo faceplate, where-as on the CB gauges, they aren't. wasn't that hard to install it. i took pics of the installation progress if you wish to see them

[Rendon LX-i]

I would love that man.

[A18A]

A few things I've been prepping for the H22 swap:

Electronic speedo conversion:
CD speedo in CA gauges
http://img839.imageshack.us/img839/9371/2583175medium2.jpg
http://img849.imageshack.us/img849/8029/2583181medium2.jpg
http://img692.imageshack.us/img692/1544/2583189medium.jpg
Trip meter reset modified to fit
http://img441.imageshack.us/img441/534/2583185medium.jpg
shitty hole melted open for trip meter lol
http://img51.imageshack.us/img51/9841/2583176medium.jpg
this is where the needle sits when there's no power, because there's no "stopper" holding the needle from dropping below 0
http://img814.imageshack.us/img814/9126/2583206medium2.jpg
12v applied
http://img849.imageshack.us/img849/4020/2583207medium2.jpg
testing it out
http://img31.imageshack.us/img31/9259/2583209medium2.jpg
success!!

[Rendon LX-i]

So that's out of a 90-93 accord?

[A18A]

dunno what year, it's from a 5th gen

[MessyHonda]

I see a coke can. Remember when monkey would post pics of pepsi?
Next weekend il see if I can find a 6k resister and see if I get a CEL since I am using a 89 cluster

[A18A]

coke is my backup for when I run out of sprite :)

or maybe I work for the Coca-Cola™ (http://www.coca-cola.com/en/index.html) and they're paying me to subliminally advertise for them

[Rendon LX-i]

Well the 6k didn't work for me. Works to a point then boom cel when I slow down.

[MessyHonda]

Well the 6k didn't work for me. Works to a point then boom cel when I slow down.

well I don't have any wires connected and the code does not go on until I let go off the gas when I'm slowing down. Did you put the resisters in series?

[Rendon LX-i]

In series? No I just cut the vss wire c1 I believe an tapped into the Blk/yel an put a 6 k resistor then from there to the vss wire I cut . Worked till I slowed down but I swapped cluster an no more vss code

[MessyHonda]

ok it sounds easy. i need to find my resistors....i know i have some around here