Come on, just one, don't be greedy!
Printable View
Come on, just one, don't be greedy!
A20a4
I'll post some this week
Pics nao.
Dam I want to see this ish to! I REALLY want a b-series now. It looks bouss. Really though any pics/updates??
im saving the pics LOL. takes time to make a nice vid to. im not that great at that kinda stuff so im trying.
Dont worry.
-_-
^^double fail^^
Ooooo like that huh. Oright
How can you have the rep of being a pic whore when you dont post pics.
Cause im on the edge of graduating and studying for my ASE test. ALot of pressure here in last 2 weeks. My career is more important then my car right now LOL.
so ill get at it once i have time. It will be a monster regradless.
Very proud of you Josh! I'm glad to see you have your priorities straight and that you are making something out of your life with a post secondary education. Us paisas have the lowest graduation percentage from HS and even even lower in higher education and you are helping to change that :)
Gotta break the chain of day labors. I help out when ever I can . I know a lot of shit now that makes passing it on knowing what I'm talking about lol. An thank u homie.
Do it rendon! Get the knowlage man!
Come on rendon ...What happened dude...Walk out snap a quick pic and post it homie... Were all waitin...
Its good to hear that you're getting your life in order and thinking about the future but you have trow us a bone or something! lol
Lol. Will look I bought some itr cams an blox cam gears . Getting the last pieces tomorrow . Axle starter. Done. So expect a running car in a week or so
Will itr cams are out of the picture. Now it's jun stage 3 cams an blox cam gears plus blox dual dual valve springs an retainers :)
check H-T in the dragracing section then fs thread, there are some parts in there that may help you out.
getting closer to being done! more pics required.
I know i know guys just hang in there. K here is the final specs of my setup. I just layed down 1500 in parts all headed my direction.
I said Fuck with the BUllshit i want 200 plus all motor straight beast mode.
Power Plant
comp ratio 12:1
b18b1 bottom Decked couple thousands
b1 rods /oversized with ARP bolts
ACL Race main/rod bearings
P30 pistons STD 81mm
Hasting piston rings
Golden Eagle LSV kit
Golden Eagle head studs
B16a head with blox Dual valve springs and titianiam retainers
Blox stage 3 Camshafts Intake Lift/duration:12.8mm 272 Exhaust lift/duration:11.9mm/280
Blox cam gears
Performer X Intake manifold
Onimi 70mm Tb
Golden Eagle Thermal gaskets
450cc Blue tops
b16 water pump an oil pump
Drive train
Y1 JDM Trans
New Bearings and syncros
Exedy stage 1 clutch kit
Fidanza 7.5Lbs flywheel
90-93 DA drive axle new
89 teg pass axle new
90-93 Mid Shaft
Motor will be going in i say bout a 1 week i hope if all parts and hurry up an get in LMFAO.
Till then......................
Awwww yeaaaaa
thats what she said LOL
what its not going yet?? lol
No I needed cams an gears but then I got out of hand lmfao. So in order to run a stage 3 cams the intake mani an valve springs needed an retainers
I cant wait till the car is done.
Same hurrr.
Josh and tim I forgot to bump our turbo threads. sorry if we were not on the list.
Sure it will be
why are u bumping the turbo threads?Quote:
Originally Posted by 89T
to make a point.
Amen
Looks super nice. It
should work out well for you.
That intake manifold sits low.
The Sleeper Beauty is Almost ready to shred the Street!!! :D Can't wait to see some videos soon! Keep up the good work Rendon.
Me to im getting pretty excited....been a long road for my gurl lol
Put it in the car already, geez :deadhorse: .Quote:
Originally Posted by Rendon LX-i
^^^wut he said.
:drooling: ^^ and what they said!
She said the SamE. but I held back lmfao
:lol: i have a feeling this monster will be ready in March ;) it has to be!
yes will be good to see this project in action. VTEC is fun
Vtech is loud.
http://carhumor.net/wp-content/uploa...ion-poster.jpgQuote:
Originally Posted by Tdurr
:ninja: gewd eye sir.
http://i728.photobucket.com/albums/w...i/ce30cfd7.jpg
http://i728.photobucket.com/albums/w...i/bf8c8900.jpg
http://i728.photobucket.com/albums/w...i/d9183efd.jpg
http://i728.photobucket.com/albums/w...i/a4779505.jpg
http://i728.photobucket.com/albums/w...i/ae2dc1a7.jpg
Blox valve train installed. Dropping in motor . So project done. Time to work on the body an suspension an wheels. Dr-20 perhaps
That thing looks beast! .......NO! Takes pics and vids of car running, post them here, we all drool, THEN work on body and suspension and wheels! lol
^ What he said! :kekeke:
Yeaaa parts are in. Vids vids vids.
is it going yet.
vids yet?
no yet. nobody had camshafts seals so i order some on rock auto. WAITING LOL
sadddddddddd
You should drop that in my mini :D
^^ I would love to see that!
Booooooooo
Agreed, that motor deserves to go into a 3gee!Quote:
Originally Posted by Tdurr
yeah it might actually make a fast accord in the end :P
OMG IT'S INNNNNNNN!!!!!! Ahhhhhhhh
.
.
.
.
.
.
.
.
.
.
http://i728.photobucket.com/albums/w...i/7f3c82f0.jpg
http://i728.photobucket.com/albums/w...i/c9c53d60.jpg
http://i728.photobucket.com/albums/w...i/dc8902ee.jpg
http://i728.photobucket.com/albums/w...i/05f931bb.jpg
Gotta install axles an do some wiring. The iac don't fit it hits the firewall. But If can notch it I'll be Oright. Hits the dog bone mount area.
Yayayay!! Finally, good stuff! :thumbup:
FINALMENTE!!!! Looks beastly bro. I can already tell that our future meet is gonna be awesome.
O yea gonna be beast
that's what she said :kekeke:Quote:
Originally Posted by Rendon LX-i
Indeeeed
Nice!! Clean swap and that engine looks mint!! How many miles on it??
None lol. Have to do a few things before I do a start up vid
MY bad I meant before you dropped it in...Did you buy it from a importer?? They normally give you a guesstimate on how many miles it has done before they sold it
ooh! I though you forgot how to use a camera My bad lol!
Lol right! No I buildt this motor from the ground Ls Vtec
that intake manifold is big. should of got a blox or skunk
You sure forgot how to text a guy back.
coughvictor \x/ cough. lol!
yes i had a victor x that i never installed but it was going to be a really nice fit on the a20
Messy it's big but if I want to break over 200 I need this intake
good shit. dyno vids after break in
good stuffffffff
Oh my. Goddamn street racers.
today after work i should have the bay buttoned up. axles installed tmount braket bolt i needed. i need to cut that old mount off to run my iac. then i need to make room for the header LOL. alot to do but not really hard part is done so just little things i need to do.
Slacker :p
Wow!
I too was beginning to think that this was just a fable, awesome to see it finally in there man.
K will it bit of a bind up I fucked up an got a Sk7-N midshaft which means its a AUTO shaft I couldn't get it to bolt to the block im like wtf. Did some research an the sk7-J is the one I need . So off to the junk yard I go tomorrow !
Nice to see this thing getting done! For a minute I thought I would never see it. lol
IM SO PROUD OF THIS CAR THE SHIT DUDE . Cant wait for first start vids .
oh the waiting
Its been 9months...
Question: where did you cut the cross member? front side? im guessing for the down pipe area to fit snug?
I mad a cross member but wasn't close. So I'm redoing another
Update. Car is almost ready to start. Got my gsr midshaft an I try to use a 89 teg driver. DIDN'T WORK. I had a 90 lude drive an it fit like a glove so I have to wait to rockauto exchanges my axle. Last night I had to chop my crossmember a lot lol. But I'm going to box it in. Looks so nice. So I'm down to wiring up the iacv an Vtec . An axle. An intake pipe.
So into for future b series swaps.
If using a cable trans as in A1,Y1,J1,S1. You need a DA mid shaft that has a female end. Anything past 93 you need to use a male style midshaft. There for you would need to use a different seal for the midshaft to put in cable trans.
But here is what I got an it works cause its in the car now.
90-93 DA pass side axle.
90-93 gsr midshaft (same as all years doesn't matter)
88-89 lude driver axle. NOT 90-91 IT HAS a bigger HUB there for wont go into ARE HUB.
But ok pic time lol
http://i728.photobucket.com/albums/w...i/ec2e1bbf.jpg
http://i728.photobucket.com/albums/w...i/4a054abf.jpg
http://i728.photobucket.com/albums/w...i/a99fc092.jpg
Driver lude axle ^^^ with da mid shaft I try to use the 89 teg was way to short.
http://i728.photobucket.com/albums/w...i/6888ff6d.jpg
90-93 DA pass side
Yesss
So you're using different length shafts on each side? Doesn't that defeat the whole point of the mid-shaft?
I thought pass side was 87? or is cause you are using LSD?
John no the 89 teg is way shorter it was my bad on my part. The lude is pretty much the same put a bit longer (1/2) inch . Either way it works. I have LSD so it work just fine lol.
This is what I have an it works with pics. No other thread has pics installed an gives detail . I hated that. I go info from couple members it wasn't sure. I didn't want to make custom axles cause I wanted to buy one if needed.
hey wat mounts r u using
^^^ read the first page...
looks good josh
So much stuff isnt clear on here. But we make do with what we got!Quote:
Originally Posted by Rendon LX-i
I basicly said its the same length on both sides . An I posted pics with info for whom wanted to do the swap. I have seen of seen pics of the axles installed.
Thanks bro.Quote:
Originally Posted by stat1K
This is the same setup so I should be smashing lol.
http://www.youtube.com/watch?v=rRL6_...e_gdata_player
