Results 1 to 3 of 3

Thread: 1G Accord Lug-Centric Hubs and Wheel Vibration

  1. #1
    LX User tof's Avatar
    Join Date
    Dec 2016
    Vehicle
    1979 Honda Accord LX Hatch
    Location
    Long Beach, MS
    Posts
    103

    1G Accord Lug-Centric Hubs and Wheel Vibration

    Pulling a wheel from my 79 Accord for the first time I was surprised to see that there was no wheel mounting flange on the hub. This means that the 1G Accord uses a lug-centric wheel mounting system. That is, it depends on the wheel studs to carry the full load of the car and the lug nuts to accurately center the wheels on the hubs.

    Most (or maybe even all) modern cars have an axle hub design that includes a flange or collar that matches the oem wheel center bore. This insures that the wheel is always mounted precisely centered and the flange also helps support the load of the car through the axle and onto the wheel. Generic aftermarket wheels generally have a large bore so they will fit over the flange on a variety of different makes of cars, since various manufacturers size their hub flanges differently. That's why hub centering rings are recommended with aftermarket rims. They effectively reduce the center bore of the wheel to match the diameter of the hub flange.

    But the hubs on a lot of older cars were not made with hub flanges but instead rely on a lug-centric mounting system. These cars rely on the tapered wheel nut to center the wheel accurately. While this can work fine, it may be less precise than a hub-centric system, especially if the lug nut seats on the wheel are damaged. This also means the wheel studs are subject to the full load of the car, unaided by a hub flange.

    To insure vibration-free operation, especially at higher speeds, extra care must be taken when mounting lug-centric wheels. Most advice I have found on the Internet suggests snugging down the lug nuts with the wheel off the ground, followed by torquing the nuts to spec once the car is back on the ground. Following the usual standard practices like tightening in a criss-cross pattern is also necessary.

    I have also read that a special procedure is required to correctly balance a lug-centric wheel and tire but I don't know if this is common knowledge down at the tire store.

    All this came up because I just bought a set of RS Watanabe Eightspoke rims and was looking into hub rings. That's when I pulled a wheel to measure the mounting flange diameter. Well...turns out I won't need hub rings because of the design of the first generation Accord hubs. I would be curious to know when Honda introduced hub-centric wheel hubs on the Accord.



  2. #2
    DX User
    Join Date
    Sep 2012
    Posts
    89
    .
    Last edited by Stealth; 10-28-2017 at 02:51 PM.

  3. #3

    Dr_Snooz's Avatar
    Join Date
    Jun 2007
    Vehicle
    1989 Accord LX-i
    Location
    Fresno, California
    Posts
    10,638

    Re: 1G Accord Lug-Centric Hubs and Wheel Vibration

    The lugs don't actually support the weight of the car. If you forget to tighten them, you'll find out very quickly that they aren't up to the task. After a few miles, the lugs will shear off and the wheel will continue bouncing down the road while you grind to a stop. I think the static friction of the wheel surface clamped to the hub surface is what carries the weight.
    Dr_Snooz

    "I like to take hammers, and just break stuff, just break stuff." - Beavis


    1989 Honda Accord LX-i Coupe, 240k miles, MT swap, rear disc swap

    Shop manual downloads available here: CLICK TO VIEW

Similar Threads

  1. Wheel bearings and hubs! $50
    By codyJDM in forum For Sale
    Replies: 0
    Last Post: 05-15-2009, 08:22 PM
  2. Steering Wheel vibration
    By nutmeg_runner in forum 3geez Accords
    Replies: 3
    Last Post: 04-05-2005, 04:05 PM
  3. Vibration - Steering Wheel
    By hkplayer in forum 3geez Accords
    Replies: 8
    Last Post: 11-05-2003, 09:02 AM
  4. Steering Wheel Vibration
    By RicanRice89 in forum Performance
    Replies: 0
    Last Post: 02-26-2003, 10:01 AM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     
Links monetized by VigLink