Golden Eagle Adjustable Cam Gear Group Buy / Formerly Fidanza

[joker2]

I'm interested, I sent you a pm Mike....

[Justanothermike]

ONE CAM GEAR LEFT!! i'm down to my last gear.

I still have 2 gears that have already been paid for but i don't have the addresses to send them to. Keith Stats and Mikes89Accord. please contact me

[rileyescobar]

when will more cam gears be made?
i've been offline for a few months now or else i'd probably know already

[Justanothermike]

when will more cam gears be made?
i've been offline for a few months now or else i'd probably know already

There is a VERY SLIM chance of more being made seeing how hard it was to get this buy to go through and how long it took. anyways there where 30 made and one lost in the mail. so for the guys that havem consider urselves lucky

[nswst8]

Can you give me an update on the shipping.
Thanks

[Justanothermike]

Can you give me an update on the shipping.
Thanks

i'm gonna see if i can ship them out today. darry currently has them in his posession

[nswst8]

I have the Camshaft and need the gears.

[nswst8]

[joker2]

When is the expected shipping date???

[Justin86]

It is so beautiful........

[Volitech]

Does anyone know what the torque spec is on the cam gear bolts? I've moved and lost the sheet that came with the gear...

[maka_RTH]

i believe it was 20 ft/lbs

[Volitech]

i believe it was 20 ft/lbs

Cool, Thanks!

[A20A1]

Was the last one sold? I need to trim these stickies cause I'm getting complaints...

_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-

CLICK HERE TO POST YOUR CAM GEAR DEGREES ( ADVANCE / RETARD )

_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-

[Robs89LXi]

i believe it was 20 ft/lbs

Be careful tightening these! I just put mine on, started at 10'#, went to 15'#, then started going to 20'#. Ended up stripping three of the four bolts! Only one held at 20'#. Anyone else had a problem with this? I'm pretty upset about it, and wrote to Golden Eagle yesterday. I did not get a reply today, so will probably call them on Monday. Just be careful when you tighten them, and it makes me wonder if they will indeed hold under use.

[maka_RTH]

mine haven't had any problems as far as i know, and they held both times i've tightened them to torque.

[RiCANACCORD]

I've been reading about this, but I need to know where's the correct cam gear setup if the car is completely stock , since you can decrease HP while adding torque with a desired setup, or viceversa.

[b8er]

alright well it seems i found this post a few days short, lol, this is the first time iv looked for a adj. cam gear, does anybody know of anywhere where i could get one, if somebody is still making them who? and if nothing else who can i buy one off, thanx for any info regarding this, email me at [email protected] or add me to msn or whatever, thanx

[HC_LXi]

Any news on when theres gonna be more adj. sprockets.i need one seriously.

[markmdz89hatch]

I've been keeping in touch with Golden Eagle on these, and due to the low demand of the gears they will not be doing any production runs of them to keep them in regular stock. These will be on a group or as needed basis only. They still have the program for the gears, but will not do a run for any less then a bulk of 30.

I'll be more then happy to run a group buy on them, but it's too early yet to start up another buy b/c there's only a few people interested in them right now. As soon as I see the need begin to grow substantially, I'll work out all the details with G/E and get another buy going. Honestly though, I don't see that happening anytime in the next 6 months unless there's a new-found interest in them again.

[joker2]

You just have to keep your eye open for guys on the board selling theirs..... I didn't buy mine until after the group buy and the only reason I got mine was because Mike had like 3 left over that people didn't pay for so I jumped on it....

[bobafett]

knock knock... anyone selling theirs? i need one! maybe i will just have a stock one modified... hmmm...