Results 1 to 15 of 15

Thread: Someone please help

  1. 08-08-2003, 03:01 PM #1
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88

    Unhappy Someone please help

    im in the middle of doing my oil pan gasket and i got all the bolts off and the flex pipe down and now it seems to be caught on the tranny or somthing i didnt take crossmeber down cuz it shouldnt be in the way. does ne one have a step my step intruction pics or somthing. thanks for the help tom
    Reply With Quote Reply With Quote



  2. 08-08-2003, 06:02 PM #2
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    thanx for the help, well ne way its out, had to take off like 3 more things, and the gasket has 3 tears so i guess thats partially the problem well ill put the new one in and see how it goes.
    Reply With Quote Reply With Quote
  3. 08-10-2003, 07:00 PM #3
    Legend-H-88
    Legend-H-88 is offline
    DX User
    Join Date
    Aug 2003
    Vehicle
    1988, Honda Accord HB
    Location
    Hueytown, Alabama
    Posts
    29
    ok dude this is the steps for removing the oil pan step by step.
    works on 1985-1989 all makes of accord and 85-87 prelude si

    1-drop the flex pipe.
    2-drop the lower crossmember (only 7 14mm bolts)
    3-there is a pipe welded into the oil pan on the back of the crank case remove the banet holder on the connecting rubber hose (that is part of the extensive pcv valve system)
    4-remove the dust cover and lower engine mount (that connected to the lower crossmember) should be 4 12mm bolts and 2 10mm bolts.
    5- remove the (three trillon 10mm bolts holding the oil pan to the block -- lol)
    6-wedge a flat tip screwdriver between the oil pan and the block and pry the oil pan loose working all the way around the oil pan.
    7-after breaking the pan loose *simaltaniously* pull the oil pan down and at the same time while pulling it towards the driver side of the car.

    thats it man. but watch your eyes, cause when the pipe lets go it tends to fling excess oil in the pipe everywhere
    Reply With Quote Reply With Quote
  4. 08-11-2003, 04:56 AM #4
    Vinny
    Vinny is offline

    Vinny's Avatar
    Join Date
    Aug 2003
    Vehicle
    2010 Ford Taurus SEL, 2010 Ford Fusion Hybrid
    Location
    Here, not there
    Posts
    4,140
    Lemme know how it comes out when yer totally done, I need to do mine here in the next few weeks
    Reply With Quote Reply With Quote
  5. 08-14-2003, 01:29 PM #5
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    ok i got the gasket and the sealant can some one give me a how to, or some pictures becuase i need to know how u use the sealant and shyt

    thanks tom
    Reply With Quote Reply With Quote
  6. 08-14-2003, 01:34 PM #6
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    i already got the pan out i just want to know how to use the sealant and shyt or see some pics on it
    Reply With Quote Reply With Quote
  7. 08-14-2003, 02:37 PM #7
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    ok cmonn 3geez PROFESSIONALS help me out i need to know how much sealant do i put and where and whats the torqueing sequence ........
    Reply With Quote Reply With Quote
  8. 08-14-2003, 02:42 PM #8
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    even if you could post some pictures from haynes repair manual would help ........
    Reply With Quote Reply With Quote
  9. 08-14-2003, 04:39 PM #9
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    thanks guys i got to get to work tommorow looks like im going to be up till midnight
    Reply With Quote Reply With Quote
  10. 08-14-2003, 05:07 PM #10
    Vinny
    Vinny is offline

    Vinny's Avatar
    Join Date
    Aug 2003
    Vehicle
    2010 Ford Taurus SEL, 2010 Ford Fusion Hybrid
    Location
    Here, not there
    Posts
    4,140
    manual says to put silicone in 4 spots on the pan, the four corners where the hump in the pan are, thats it, then put the gasket on over the 4 spots.
    Reply With Quote Reply With Quote
  11. 08-15-2003, 05:30 PM #11
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    aiight guys all done no leaks from the pan now but there was a tiny leak be4 they guy had messed the oil pan gasket up and now i fixed the oil pan gasket and its got the real little leak but its weird the little drips are comming from the iming belt cover area
    Reply With Quote Reply With Quote
  12. 08-15-2003, 06:31 PM #12
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    its like a lil more then a teaspoon afta a 30 min drive comming from the timingbelt bottom , and there is some weird noise when u give it more gas than normal driving or givin it alot it like clings or pingin or suttin i wanna fix that
    Reply With Quote Reply With Quote
  13. 08-16-2003, 08:36 AM #13
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    also where would my timing mark be we looked all over
    Reply With Quote Reply With Quote
  14. 08-16-2003, 08:39 AM #14
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    also im getting a clicking from my distributor
    Reply With Quote Reply With Quote
  15. 08-16-2003, 11:27 AM #15
    88AccorD4Life
    88AccorD4Life is offline
    DX User 88AccorD4Life's Avatar
    Join Date
    Jan 2003
    Vehicle
    1989 Accord Se-I
    Location
    Rehoboth, MA
    Posts
    88
    cmon ppl
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     
Links monetized by VigLink