my choice of amps

[accordlxi2.0]

9x's outta 10 yall naming things that are expensive as hell

[Bloodlust]

I add this, Jenson does indeed suck. Go with the Kenwood 4-channel. I have one in my car and i have never had a problem with it. Best you can get for your money and you dont have to deal with running 2 amps just for speakers.

[accordlxi2.0]

i'm not a fan of jensen either, . . . . . . i was gonna get that profile but . . .
come to find out my dad went to sear's and got a jensen jxp680.
why . . . . 1) it's on clearance and it was pretty cheap even though reg price was $200.
2) he said that jensen is a good brand and that he had a set of speaker's and they lasted for a long time and they sound pretty good.
plus it was a gift, so . . . . . .
i know, i know guys but, this is my dad here and i really don't ask for much ( i do them or buy them myself)
that 140 can now go torwards the tune-up.
. . . . . . . . . . . . . . . . . . .

[accordlxi2.0]

okay . . . he gave me the recept to take it back, he was kinda upset cause he think or belive that jensen is a good brand . . . . .
i told him what y'all went through and he was like . . .
anyway look i'm need y'all assitance again
i seen this it's a baja profile amp here are the spec's:

it's mosfet powered
400watt's (200w x 2) 4ohms
150 rms x 2 @ 2 ohms
speaker level inputs
bridgeable
thd <0.07
variable bass boost
switchable crossover
variable crossover feq 40-130hz

they are about $45

the only problem is i wanna 4channel which mean's i would have to get for they're on sale for a low price, but's it where i would have to munt them is the problem, then i would really have to get a cap.

then there's a few more like these:
MODEL KS-AX4550 4-CHANNEL SHAUN PALMER SIGNATURE SERIES BRIDGEABLE MOSFET HIGH-POWER AMPLIFIER
MOSFET power supply
Die-cast aluminum housing
SOHC—Super Optimum High-power Circuit
Maximum power output: 520 Watts. RMS power: 50 Watts/channel into 4 ohms. Selectable 4/3/2-channel operation. With speaker input terminals. Virtually distortion free: 0.04%. 4-way protection—heat, overload, short circuit and DC offset. 2-ohm stable operation. Variable input level control (0.3-5V). Bass boost control. HPF/LPF/off switch. Anti-pop circuit. Gold-plated RCA jacks and power input terminals. Frequency response: 10-50,000 Hz. Approximately 9-3/16"W x 2-7/8"H x 14-5/8"L.

cost $189

then there's this one:
1000-WATT 4-CHANNEL HIGH-PERFORMANCE AMPLIFIER
Red Elite Series (red and black with silver-color trim)—your best choice for quality, big power and great looks
Two variable high/low electronic crossover networks
Bridgeable MOSFET power supply
Two variable bass boost. Remote bass boost. Variable gain control for best hookup to your system's components. Thermal/overload/short circuit protection. Almost no distortion—less than 0.04% THD. Red Elite Series features include: blue LED power-level display; power-on and protection LED indicators; anti-thump turn-on. With gold-plated RCA inputs, high-level Molex input. S/N ratio: over 95 dB. Frequency Response: 15-30 kHz. Peak Output: 1000 Watts (250W x 4). Bridged Output: 500W x 2 or 250W x 2 + 500W x 1. Measures: 12"W x 2.7"H x 10.9"L.

cost $144


SO WHICH ONE DO YA THINK?????????

[accordlxi2.0]

can anyone make a suggestion . . . . . .again?????

[oneslammedlxi]

go with a sony xplod 4 channel 1000w amp, you can find them for mad cheap, and there decent amplifiers, i run one bridged (500x2) on my 12" rhinos

[accordlxi2.0]

okay i took your advice dan, dx spuared, accordepicenter, i found some profile BAJA amp's at circuit city for about $30-40 apice ,plus i got a 4year warranty so i have 2 two channel amp's they're not that big and they look nice, plus one thing's for sure when i opened the boxes it did'nt smell like the amp has burned out like the jenson did, thanx yall basically saved me i hope