FS: ACT Clutch, Full Exhaust and More

[ryan88lxi]

I still have a few things for sale. everything is in great condition!

A20A3 Engine - complete engine bored .020 over. new oil pump. comes fully assembled with a gude ported and polished cylinder head. head is able to handle 11.1:1 compression. 2 way race valve grind. complete with gude camshaft. 282 duration 434 lift. stock cam gear. 950$ will not ship, buyer is going to have to meet me half way or something like that.

ACT Clutch: ACT heavy duty pressure plate, ACT street/strip disc. This clutch has about 15K miles on it. last time i drove it, clutch bit very hard, it will let you chirp third if you have enough power (which i did) still plenty of life left on it, 200$ takes it!

DC Sport/Custom/HKS Full Exhaust System: This is a custom exhaust from a dc sport header, welded to a catco catalytic converter for a v8, into 2.5 inch piping, to an HKS hi - power muffler. i spent 900$ on this exhaust including labor. there are a couple minor details with the header, if you are interested in it, ask me and i will let you know. 400$ takes it

Eibach Sportline springs - less than 1000 miles. 140$ and theyre yours

Gude ported and polished intake manifold - 150$

Gude bored throttle body - 100$

Also, i can part out anything wants off of it aside from the hood, fenders, and bumper. It is a blue 4 door lx-i with a blue interior. if you need anything let me know and we can figure something out. i will prolly add a few things as well. PM me for more info or ask me here. thanks everyone

[markmdz89hatch]

Are you willing to trade for anything?

[i.c.]

umm....how are your front speaker wires and rear baskets?

[od2681]

what kinda rims do you have..or do you have any???

[ryan88lxi]

unless you have parts for jeep xjs, im not too interested in trading.
speaker wires are fine im sure, but not worth the time.
stock rims

[86LXi|JustONE]

rocker arm, cv boot, right axel, the peice that hold the wheel, and your struts and rotors. see how much that will be and holla back....only the front, right side if you can....

unfortunitally i wrecked my car cause this old ass bitch cut me off so i spiked my brakes and hit a curb...my wheel got pushed back 6 inches and the rocker arm is broken...also the strut is bent probably a few more things as well but those are what i see without taking it to the family mechanic...im looking on probably getting most of your drive shaft such as trans axels and axel...but like i said thats after i talk to the family mechanic...so get at me with prices and well be in contact

[ryan88lxi]

when i start taking everything apart, i will let you know. i will be disassembling everything this week

[Elijah]

If you give me about a week. Mabey less I will take the manifold and throttle body.

[accordlxi2.0]

i PM ya.

[86LXi|JustONE]

awsome man just get at me through PM or aim ok...im highly interested if the price is right

[jugglaccord17]

ill give u 140 for just the header! i have everything else back from that!

[ryan88lxi]

PMs have been answered

[ryan88lxi]

bump

[Bloodlust]

I call dibbs on the FULL EXHAUST.

[ryan88lxi]

blood has dibs and the tokicos are back for sale for 200 + ship

[BITESIZE]

Act clutch for $200? Used with 15,000 miles on it?

[ryan88lxi]

yes

[BDaccordguy]

what do you have in terms of console? If you have the front half of the center console with a tape holder i will be interested

[ryan88lxi]

i have the tape holder, its blue

[BDaccordguy]

what kind of shape is it in and what do you want for it?

[ryan88lxi]

what kind of shape is it in and what do you want for it?

its in good shape, the whole interior is. i dont know what people usually pay for these but 20 bucks plus shipping should do the trick.

[ryan88lxi]

still for sale!

[cahil_1]

yo, what about the transmission? what shape is it in? has it been rebuilt. do you Have it still and what for it. i'm lookin to do a tranny swap A to M.

[ryan88lxi]

i think hostilejava has dibs on that, we were talking about it earlier in the thread

[86LXi|JustONE]

aye man what ever happen to parting out with the underside...axels and what not have you dismantled yet or have things changed...get back to me in a PM