got some presents

[87lxiaccord]

so i decided to order a 5g accord cai after seeing monkeys and thought it would be easier to install and with less bends...I didn't have to cut the intake at all or take the horn out we made the hole in the fender bigger and moved the battery tray like an inch to the drivers side and drilled new holes to screw it onto the bracket then we mounted the tie down on the other side.





other stuff that i will be putting on in a couple of days. I also put on a 1stgen integra lip and cut the ends to make it fit the 86-87 bumper it came out good but i forgot to take pictures. When we took my car for a little spin after the intake my clutch started slipping up it must be that extra horsepower...lol so i'll be replacing that too im thinkin an exedy one will do just fine.

[hotdoghogie]

damn how mcuh was all of this?

[87lxiaccord]

around 600 and i have to get the header welded by my friends dad there is an extra egr tube hole and 2 o2 sensor holes

[ghettogeddy]

what header is that and how much did u get it for

[87lxiaccord]

its the pacesetter it was 240 including shipping...wasn't too bad considering it's the coated one and it was the cheapest one on ebay at the time

[ghettogeddy]

give me the link for the dealer i might ick a set up oh and y dident u use the bypass filter on your intake

[cubert]

blah..makes me jealous...i cant wait to get the header and intake for my civic

[87lxiaccord]

i tried to get the bypass filter to fit but there wasn't enough room i can always put it on if i cut the first pipe but i think i'll just keep the short ram in the trunk and switch it out when it starts raining.
http://cgi.ebay.com/ebaymotors/Paces...spagenameZWD1V

[shepherd79]

damn, that is the cold air intake i got. I haven't installed it yet because i need to drill 3 wholes for the vacuum lines.

How much bigger did you have to cut the opening in the fender for the pipe to slide through?

[EricW]

Nice stuff. Didn't you have a P&P head on the car already.

[87lxiaccord]

about 1 inch all the way around we used the good old sawsall

[87lxiaccord]

yeah we did the port n polish over the summer and port matched the manifolds

[EricW]

yeah we did the port n polish over the summer and port matched the manifolds

Then that intake and header should make a nice difference.

[87lxiaccord]

yeah i was thinking the same thing along with the coil and some new wires. I want to start auto crossing so right now i have my eye on the ST sway bars and maybe my friends dad will be able to mod a set of 4g strut bars then in the future an se-i rear brake setup with 11 inch rotors up front and some 15" rims

[MessyHonda]

nice stuff man...the intake looks good....to bad i already bought my teg one. dont weld the header...from wut i heard you can use a oil drain plug to plug em up. plus you are messing with a 240 dollar header...if you part it out you will get more money.. i also got the same header..but i want to use the DC primaries and the pacesetter downpipe. hope it works for me. how much did you get the delta for and wut grind did you get? i have an extra cam shaft but im just lazy...to send it in...now...it looks hot...i wanted a colt tho.

[snoopyloopy]

wonderful. i know what my next mod might be. which also means i'll soon have a 2g teg cai for sale.

[87lxiaccord]

nice stuff man...the intake looks good....to bad i already bought my teg one. dont weld the header...from wut i heard you can use a oil drain plug to plug em up. plus you are messing with a 240 dollar header...if you part it out you will get more money.. i also got the same header..but i want to use the DC primaries and the pacesetter downpipe. hope it works for me. how much did you get the delta for and wut grind did you get? i have an extra cam shaft but im just lazy...to send it in...now...it looks hot...i wanted a colt tho.

i know it sounds risky to try an weld but i won't be cutting then welding it back together im just gonna weld a plate over the extra egr tube hole and o2 sensor hole. Also my friends dad is very experienced in welding his work is great. The cam is a 272 and it was around $85 but i will send my core in and get $30 bucks back

[Cheeseburger]

cant wait to see it on the car maing

[MessyHonda]

i know it sounds risky to try an weld but i won't be cutting then welding it back together im just gonna weld a plate over the extra egr tube hole and o2 sensor hole. Also my friends dad is very experienced in welding his work is great. The cam is a 272 and it was around $85 but i will send my core in and get $30 bucks back

holy shit...i need to jump on that...so for 55 bucks i can get a cam....woot.

[Cheeseburger]

dam that is cheap....

[snoopyloopy]

shit, son. soon as i get paid again, i might get one too.

[87lxiaccord]

so we welded my header tonight and it came out pretty good i also opened the holes on the flange up and grinded down some rough spots...


before

after

[MessyHonda]

look good man.

[LiTtLe xOx BitT]

Why did you weld up one of the o2 sensor holes? I know the other hole you welded is only for the carbed engines, but i have 2 o2 sensors on my car.

[Cheeseburger]

so do i, isnt the car going to run like crap with out them