11" REAR rotors + Bigger Calipers

[Legend_master]

Disclaimer: This mod has not been tested on a driving car. The issue with the rattle brackets has not been worked out yet.

Ok to start off, this is what you need.

• 1988 - 1989 Accord SE-i rear disk conversion (kinda a given)
• 1988 - 1989 Acura Legend Caliper and bracket
• 1988 - 1989 Acura Legend brake pads
• 2000 Civic SI Powerslot 11" rotor Part#'s 29-900L and 29-900R (I purchased mine at www.buybrakes.com) You have to call them, because the part is not listed.

First you must modify the Legend Caliper bracket to allow for the larger rotors. I jsut used a file to take away the little bit of metal that had to be removed.

The unmodified bracket is on the left and the filed down one on the right


before

After

A little shot to show you what it looks like in the process of being modified

I am sure every setup will be jsut a little different since all parts are not made equal. I will show you how to figure out what parts of the rotor touch the bracket.
I bolted the bracket and rotor on then turned the rotor to figure out what part of the bracket touched the rotor.

Next you must modify the dust sheild (or completely remove it) the Legend bracket is a little larger then the Accord.
First roll the edges
Before

After

This picture shows where it must be folded

Continue onto next post.

[Legend_master]

Last thing you need to modify is metal brackets that keep the pads from moving back and forth. I had to remove the middle piece that hold it in place.





Here is what the pad look like without the caliper.



Final Product

[mkymonkey]

thats it? all you do is blot up the caliper and put it back on the car? cool....
and now comes the important question. how much did you end up spending?

oh oh oh and what is the smallest wheel you think this will work with? 15 i presume...since thats what you have lol

[Legend_master]

thats it? all you do is blot up the caliper and put it back on the car? cool....
and now comes the important question. how much did you end up spending?

The rotors are only $100 a piece. Calipers + brackets were $15 each from the JY and new calipers are $50 a piece from autozone. + the price of the disk conversion and the pads (about to get some EBC's) .

[Legend_master]

oh oh oh and what is the smallest wheel you think this will work with? 15 i presume...since thats what you have lol

Yep 15's and nothing smaller.

[87lxiaccord]

sweet build man i will definetly look into this after finding an se-i at the jy maybe i will get lucky...

[mkymonkey]

cool....now i have to just do your front disk swap and then do this one. i already have the rear swap so i just have to purchase the rest. i knew you would work it out...haha so i waited

you sir are a true pioneer

[guaynabo89]

Last thing you need to modify is metal brackets that keep the pads from moving back and forth. I had to remove the middle piece that hold it in place.

Theres a problem if you do that to that clip. It will now be able to move back and froth and touch the rotor giving you an annoying grinding sound.

Other than that looks great.

[Legend_master]

Theres a problem if you do that to that clip. It will now be able to move back and froth and touch the rotor giving you an annoying grinding sound.
Other than that looks great.

I was thinking this also, but as I have played with it over and over, and the pieces never move, because the pads keep it stuck in place. This is something I plan on tackling after I install them on the car. If they do rub, I will have to make something up after I install them.

[MessyHonda]

man looks good....i did end up spending like 300 bucks for my rear disk set up when i could of upgraded....oh well maybe when this set it is all gone il upgrade. thanks for the research maing

[ZackieDarko]

this will be sexy on my new rear disc setup in 1-4 weeks

[Legend_master]

man looks good....i did end up spending like 300 bucks for my rear disk set up when i could of upgraded....oh well maybe when this set it is all gone il upgrade. thanks for the research maing

Definitly equal to the price of nice pads and D/S Rotors.

this will be sexy on my new rear disc setup in 1-4 weeks

Make sure to check out those shock bushings before you install them on your car. My first set of SE-i hubs were fine, but the set pictures above had bushings that were shot.

[ZackieDarko]

gotchya

[hotdoghogie]

hey there is an se-i at my local junk yard... what all do i need to snatch off of it in order to convert my lxi... i love this setup... i want it!

[Legend_master]

hey there is an se-i at my local junk yard... what all do i need to snatch off of it in order to convert my lxi... i love this setup... i want it!

All you need to grab is the rear hubs themselves, the arm that runs frot he front to back of the car, the hard and soft brakes lines (I would order braided brake lines to replace the soft ones), the bracket that connect the hubs to the arm, and then all the pieces that I listed in the first post.

[thegreatdane]

sick

[Legend_master]

sick

Well, Thank you .

[Legend_master]

Requested to have this moved from "How to" since I haven't ever actually been able to test this mod out. I'm gonna work on a bolt up option for this as well, so Ill update as I get more info.

[Honda_Hobby]

Nice if you have the tools to do your own work.

[Slipup]

I was thinking this also, but as I have played with it over and over, and the pieces never move, because the pads keep it stuck in place. This is something I plan on tackling after I install them on the car. If they do rub, I will have to make something up after I install them.

So seeing how old the post is, I'd assume there was not a issue with this?

My bad failed to read the 5-14 post. If you get it bolted up let me know, if not I'll work with it in about a week or two before I go to the field.

[Legend_master]

So seeing how old the post is, I'd assume there was not a issue with this?

My bad failed to read the 5-14 post. If you get it bolted up let me know, if not I'll work with it in about a week or two before I go to the field.

Looking at it, the mod is very possible. Just gonna take some time, research, and some cash.

[Slipup]

Alright thanks. Not sure how much cash I'll have left over once I finish changing some things next week. I'll try to run down to the local pick and pull and try and get at least the calipers and brackets. Once I get the rotors I'll see if I can come up with anything.

[turabaka]

What was the issue with this mod? Why doesn't it work?

[Slipup]

I believe the issue is with the metal pieces that hold the pads in place.

[Legend_master]

What was the issue with this mod? Why doesn't it work?

I believe the issue is with the metal pieces that hold the pads in place.

That is part of it, the rotor goes right to the very edge of the caliper and doesn't allow any room for the rattle bracket. I was thinking about running it without the rattle bracket in there, but I think the pad will shift around and cause problems/noises. Otherwise its almost a full bolt on application.