ok, i just got new door handles from majestic honda and they didn't come w/ a lock cylinder holder (the grey piece that holds the lock inards. i was wondering how to take that piece out to swap the locks into the new handles. i've tried searching but can't find anything on the forum or in the honda manual.
"Eat, Drink, and be Merry!"
i've got everything out (the lock and all) and i can see the two holes on the outside of this piece, but i can't get anything to pinch them in and to slide it out. thats the way i've been trying and if its that then is there a special tool to use or anything?
"Eat, Drink, and be Merry!"
I remember using an icepick or something similar to bend the clip in, then just pushed it out from the front...
88 LX-i coupe auto (241K DD), 88 LX-i coupe 5-speed, 89 SE-i coupe auto.
CARDONE SUCKS.Originally Posted by stat1K
Are you talking about a snap ring? From the way you guys are describing it , it sounds like a snap ring. And snap ring pliers would be the "special tool" you would use.
My other car gets about 6 miles to the gallon.
69' Chevelle SS396
89' LXi
ASE Master tech
nah, the one with the two holes on the outside of the whole configuration, i've got the snap ring off, i've got the plastic clip attachment off (to the lock pole), and i've got the lock mechanism out, all thats left is the grey metal casing that lines the two extensions from the handle. the two extensions have a hole on the outside of themselves that you can push the tip of a thin screwdriver in and will kinda push in and unclip, problem is it looks like you have to do that from both sides at the same time and then slip the metal piece out. there is no place for pliers as they are too big, and i've tried using 2 screwdrivers from either side and they don't make a diff, let me try to take a pic actually
"Eat, Drink, and be Merry!"
fuck, can't get a pic right now (batteries are dead) but its like the last thing that could possibly be held into the old handle and that would support the locking pins and shit in the new one
"Eat, Drink, and be Merry!"
Which part?
88 LX-i coupe auto (241K DD), 88 LX-i coupe 5-speed, 89 SE-i coupe auto.
CARDONE SUCKS.
on that, its a grey part thats right above the number 24 and it looks like it should slide out of that hole if you push in clips by working something thin through two holes on the actual handle piece. i ordered whats marked at 9 and 17 there for my two handles and that piece didn't come w/ it, so its actually part of the lock pieces marked 10 and 11. i'm prob gonna go around today and find a body shop or something today and see if they can figure it out if i can't get it out myself.
"Eat, Drink, and be Merry!"
#25, right above the lock cylinder, very top of the handle? It's a threaded pin (18) that presses into a 3 or 4 tabbed plastic clip (25). You won't get that sob out of there without breaking it. You need to screw the entire handle on the threaded rod as an assembly. It's annoying, but you can do it. My new handles came with 18 and 25 installed, so I guess that's how honda expects you to do it... You cannot buy the clip separately. If your handles didn't come with them, I would suggest trying to cut the metal to the sides of the clip with some diagonals. If you're careful, they can be removed and installed on the new handles.
88 LX-i coupe auto (241K DD), 88 LX-i coupe 5-speed, 89 SE-i coupe auto.
CARDONE SUCKS.
nah, its like part of the lock, you can take the innards of the lock out of it by pushing them out the front of this piece (after taking the chrome part off). say your looking at the handle from the front (outside the car), looking into the lock, you can pull the part that the key fits into out, but theres a grey metal sleeve thing around it thats attached to the body colored part of the handle still there, its that part.
"Eat, Drink, and be Merry!"
That's what I was talking about in my first post. You got it wrong, the lock cylinder pushes out the back side of the handle. There will be a slot next to the cylinder with a clip inside. Bend the clip in towards the cylinder, and push it from the front, out the back. You can leave the chrome dust cover on it. Be careful, the pins will want to fall out when you remove the cylinder, you need to keep them in order.
88 LX-i coupe auto (241K DD), 88 LX-i coupe 5-speed, 89 SE-i coupe auto.
CARDONE SUCKS.
alrighty, i'll take a look at it again, thanks
"Eat, Drink, and be Merry!"
ah ha, after pulling that piece out (rather, bending the metal away and dropping it out) and replacing the locks, the accord is once again a 3 door
"Eat, Drink, and be Merry!"
Posting Permissions
Reply With Quote
Bookmarks