4g distributor adapter for obd-1 conversion

[A20A1]

So heres what i was thinking of.

very professional I like your solution

[crucial]

My mastercam rep gave me a link to download it. Ill be out of town for the holidays, but ill get it done as soon as possible. My girlfriends dad offer to run them when we have a finished product at no cost cause he thinks its cool what we are doing and theve be really slow in there cnc department(for like 5 months).

[crucial]

very professional I like your solution

Thank you but i figered out the problem and it will be straight though which is better for flow, Can't be restricting are coolent now can we.

[LX-incredible]

My mastercam rep gave me a link to download it. Ill be out of town for the holidays, but ill get it done as soon as possible. My girlfriends dad offer to run them when we have a finished product at no cost cause he thinks its cool what we are doing and theve be really slow in there cnc department(for like 5 months).

Cool man! Have a good trip!

[jdaddy88lx-i]

glad to see you're out and safe those charges probly be dropped since you were swinging at four dudes and he just stepped in. keep up the good work and keep those stiches clean

[crucial]

The pin hole is perpendicular to the key teeth on the stock key.

The ring groove and pin hole need to be moved down 0.75" and offset around 70 degrees or so... I'll figure that out later.

Is the .159 hole a through hole?

[crucial]

Hey i was wondering if you could do a new post with all the dimensions for the key so i don't have to keep scrolling up and down to look for them. It would make it a little easer.

[lostforawhile]

hey crucial,working out a deal to get an aluminum valve cover then i can get started on the other project i was talking to you about lol. glad your not in the slammer.

[crucial]

Thanks lol.

[LX-incredible]

Is the .159 hole a through hole?

Yes.

[LX-incredible]

Hey i was wondering if you could do a new post with all the dimensions for the key so i don't have to keep scrolling up and down to look for them. It would make it a little easer.

The pin hole is perpendicular to the key teeth on the stock key.

The ring groove and pin hole need to be moved down 0.75" and offset around 70 degrees or so... I'll figure that out later.

That should be it... Let me know if you need anything else.

[crucial]

Thank you

[crucial]

Does this groove go all the way around the part?

[LX-incredible]

yes

[crucial]

Ok im gonna do the groove, outer and inner diameters on a manual lathe. Then the teeth and through hole and a cnc mill, that way the part is truly round.

Hows the bottom of the key connect to the original teeth?
Does the pin go straight through it?

Never mind i see.

So is the through hole still in the same place?

[LX-incredible]

The original hole is perpendicular (90º) to the key teeth. The new key will need it to be offset an additional 117º.

So looking at the toothed end, 153º CCW from the key teeth, 27º clockwise.

The hole will be centered on the 0.946" width, not to the side like the teeth.

Let me know if there's anything else, thanks.

[stat1K]

so anything?

[LX-incredible]

so anything?

Not yet.

[stat1K]

for shizzle.

[labeledsk8r]

whats the statuson this? is crucial missing in action??... i gotta pm you on a qoute for another small side project aswell

[stat1K]

yep he's mia

[2drSE-i]

hope he didnt wind up in jail....

[LX-incredible]

Dammit... so close.

[stat1K]

sigh at least you got a paper weight out of the deal.

[LX-incredible]

A damn fine one too...