Come on, just one, don't be greedy!
Come on, just one, don't be greedy!
A20a4
I'll post some this week
200+ ALL MOTOR LS VTEC
Dam I want to see this ish to! I REALLY want a b-series now. It looks bouss. Really though any pics/updates??
Low loud lovin it!
bosozoku inspired 86 LX-I hatchie
~~~~~~~IG @the_boso_3g~~~~~~~
im saving the pics LOL. takes time to make a nice vid to. im not that great at that kinda stuff so im trying.
Dont worry.
200+ ALL MOTOR LS VTEC
Ooooo like that huh. Oright
200+ ALL MOTOR LS VTEC
How can you have the rep of being a pic whore when you dont post pics.
Cause im on the edge of graduating and studying for my ASE test. ALot of pressure here in last 2 weeks. My career is more important then my car right now LOL.
so ill get at it once i have time. It will be a monster regradless.
200+ ALL MOTOR LS VTEC
Very proud of you Josh! I'm glad to see you have your priorities straight and that you are making something out of your life with a post secondary education. Us paisas have the lowest graduation percentage from HS and even even lower in higher education and you are helping to change that
Gotta break the chain of day labors. I help out when ever I can . I know a lot of shit now that makes passing it on knowing what I'm talking about lol. An thank u homie.
200+ ALL MOTOR LS VTEC
Come on rendon ...What happened dude...Walk out snap a quick pic and post it homie... Were all waitin...
Its good to hear that you're getting your life in order and thinking about the future but you have trow us a bone or something! lol
Last edited by obdriver6; 02-02-2012 at 09:21 PM.
Lol. Will look I bought some itr cams an blox cam gears . Getting the last pieces tomorrow . Axle starter. Done. So expect a running car in a week or so
200+ ALL MOTOR LS VTEC
Will itr cams are out of the picture. Now it's jun stage 3 cams an blox cam gears plus blox dual dual valve springs an retainers
200+ ALL MOTOR LS VTEC
check H-T in the dragracing section then fs thread, there are some parts in there that may help you out.
getting closer to being done! more pics required.
I know i know guys just hang in there. K here is the final specs of my setup. I just layed down 1500 in parts all headed my direction.
I said Fuck with the BUllshit i want 200 plus all motor straight beast mode.
Power Plant
comp ratio 12:1
b18b1 bottom Decked couple thousands
b1 rods /oversized with ARP bolts
ACL Race main/rod bearings
P30 pistons STD 81mm
Hasting piston rings
Golden Eagle LSV kit
Golden Eagle head studs
B16a head with blox Dual valve springs and titianiam retainers
Blox stage 3 Camshafts Intake Lift/duration:12.8mm 272 Exhaust lift/duration:11.9mm/280
Blox cam gears
Performer X Intake manifold
Onimi 70mm Tb
Golden Eagle Thermal gaskets
450cc Blue tops
b16 water pump an oil pump
Drive train
Y1 JDM Trans
New Bearings and syncros
Exedy stage 1 clutch kit
Fidanza 7.5Lbs flywheel
90-93 DA drive axle new
89 teg pass axle new
90-93 Mid Shaft
Motor will be going in i say bout a 1 week i hope if all parts and hurry up an get in LMFAO.
Till then......................
Last edited by Rendon LX-i; 02-07-2012 at 02:26 PM.
200+ ALL MOTOR LS VTEC
thats what she said LOL
200+ ALL MOTOR LS VTEC
what its not going yet?? lol
No I needed cams an gears but then I got out of hand lmfao. So in order to run a stage 3 cams the intake mani an valve springs needed an retainers
200+ ALL MOTOR LS VTEC
Bookmarks