Page 3 of 3 FirstFirst 123
Results 51 to 58 of 58

Thread: Who wants to help install a Weber?

  1. #51
    LX User 91lowrider's Avatar
    Join Date
    Feb 2012
    Vehicle
    85 Accord LX (carbed)
    Location
    Cleveland, GA
    Posts
    155

    Re: Who wants to help install a Weber?

    Well my boss has a wood one on his big block in his blazer and it seems to run good. He has drove it cross country with it. Could possibly spray a sealer coat on it so it would soak up the gas. Im gonna talk to him tomorrow.

    As for the driving of it, it had a dead spot up until 10mph then it had the throttle respond i would want. Shiftpoints are almost where i want them. I run 55mph alot and where its at it runs 3k rpm at 55 but as soon as i hit 60 it will shift. Its almost there. Little more tweaking and i think she will be there.



  2. #52
    LX User 91lowrider's Avatar
    Join Date
    Feb 2012
    Vehicle
    85 Accord LX (carbed)
    Location
    Cleveland, GA
    Posts
    155

    Re: Who wants to help install a Weber?

    Well here it is. What do you all think? This is a 1/2in maple spacer that my boss and I made today. It wont be till tomorrow afternoon before i can try it out.




  3. #53
    LX User 91lowrider's Avatar
    Join Date
    Feb 2012
    Vehicle
    85 Accord LX (carbed)
    Location
    Cleveland, GA
    Posts
    155

    Re: Who wants to help install a Weber?

    Ok so i couldn't wait lol. I went out there and installed it to make sure it seals good. And it does. Now to change the oil pan gasket. Also, my three lights on the dash (oil filter, oil change and service interval) are red. What does that mean and how do i get them to change back? Oil and filter are new, maybe 200 miles on them.

  4. #54
    LX User 91lowrider's Avatar
    Join Date
    Feb 2012
    Vehicle
    85 Accord LX (carbed)
    Location
    Cleveland, GA
    Posts
    155

    Re: Who wants to help install a Weber?

    Well i recieved my oil pan gasket today. I have everything off and ready to be cleaned and reinstall. Just have to go pick up some mineral spirits and rtv then ill be in business.

  5. #55
    LX User 91lowrider's Avatar
    Join Date
    Feb 2012
    Vehicle
    85 Accord LX (carbed)
    Location
    Cleveland, GA
    Posts
    155

    Re: Who wants to help install a Weber?

    When adjusting the float level in a weber, is there a difference between dgv and dgs? I know the dgv float level but am wondering if my dgs would be the same settings.

  6. #56

    2oodoor's Avatar
    Join Date
    Jun 2006
    Vehicle
    86 LX JDM B20A
    Location
    Georgia-lina
    Posts
    9,062

    Re: Who wants to help install a Weber?

    Yes i would think , because you're measuring float drop and the tOp hats are about identical.
    The differences in float level basicly depend on engine, sea level, and emulsion tubes .
    Text me if you need anything, I have a weber book and carbs unlimites has info sheets on all webers.

  7. #57
    DX User huntz0r's Avatar
    Join Date
    Dec 2009
    Vehicle
    84 Accord hatch
    Location
    Charlotte, NC
    Posts
    51

    Re: Who wants to help install a Weber?

    Just a guess but I'd try an unbent paper clip in each of the little slots beneath the maintenance indicators. Mine haven't come on yet or I would have tested this theory already.

  8. #58
    LX User 91lowrider's Avatar
    Join Date
    Feb 2012
    Vehicle
    85 Accord LX (carbed)
    Location
    Cleveland, GA
    Posts
    155

    Re: Who wants to help install a Weber?

    Quote Originally Posted by huntz0r View Post
    Just a guess but I'd try an unbent paper clip in each of the little slots beneath the maintenance indicators. Mine haven't come on yet or I would have tested this theory already.
    In the manual it says to use the car key in those little slots underneath to reset them.

Similar Threads

  1. 32/36 Weber install
    By t-bone in forum 2geez Accords
    Replies: 20
    Last Post: 07-31-2009, 11:44 AM
  2. ok ive searched weber install q's
    By mykwikcoupe in forum Carburetor Tech
    Replies: 8
    Last Post: 03-06-2006, 08:41 PM
  3. Weber Carb Install
    By 87DX in forum 3geez Accords
    Replies: 4
    Last Post: 04-16-2003, 12:16 PM
  4. Weber install ?'s
    By cspeed in forum Carburetor Tech
    Replies: 7
    Last Post: 04-07-2003, 07:10 PM
  5. Weber Install
    By dXsquared in forum 3geez Accords
    Replies: 3
    Last Post: 11-14-2002, 05:18 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     
Links monetized by VigLink