muffler hangar mod again, better shot of it
yeah, P165/50/15 look like crap too and ride like a mule wagon, but they were free and got me rolling at the time
muffler hangar mod again, better shot of it
yeah, P165/50/15 look like crap too and ride like a mule wagon, but they were free and got me rolling at the time
Last edited by 2oodoor; 06-11-2012 at 07:46 AM.
lostforawhile
That's an airplane on wheels. You have me beat!
accordb20a
yes, those are cerwin vega house tweeters
they barely work anymore but I left them there to cover the gaping hole
there are some Kenwoods on the dash now
Hazwan
That's 1 computer more than the car came with so yes!
Cygnus x-1
I've seen a lot of cars with wooden bumpers, but you at least covered it up
Dr. Snooz
I just made a few wraps on the brake with electrical tape to keep it snug and slipped it on
Roodoo
Nice work on the exhaust. Is that an a20 intake? did you have to mod the intake pattern?
Eric
3geez member since October 12, 2000
"All this worldly wisdom was once the unamiable heresy of some wise man." - Henry David Thoreau
Lightweight front and rear bumper supports.
Keihin with metal Epoxy mini stacks
Bench Seating?
Rivet Hood, hot air comes out and goes back into the hoodscoop. This is a junk hood from one of my then, three 3G's I used to experiment on.
Filled in center trunk, I tried to weld it but I was just beginning and realized just how fast burn through occurs with flux cored wire.
Muffler Tip used as intake adapter.
Partially striped interior
Last edited by A20A1; 06-14-2012 at 09:04 AM.
- llia
Yes POS carb that is an A20 intake manifold, the flange actually matches perfect but I modified it. I started out just taking of some material so it would be easier to access the mounting nuts then I decide to sans the egr system completely, also removed some bumps and uglys.
this is all old pics already posted here in various places. I need some new ones, I has more wtf'z
I experimented with some professional vinyl, it is black but turns gold when light shines on it. Radiator support needs some work to get the headlight doors aligned.
My awesome cowl hood.
Then I decided to paint it.
Now that I have ITBs I don't need a hood with a hole in it. I actually have a spare too. I should put it on someday.
C|
my 4age itbs bolted straight to the motor without any port matching was lol worthy
^^^ that Does look at home on there yes
I have most of that carb, I was rebuilding it but my box with all the small screws, linkages, and needles for the secondary have gone missing. I also have the Holley 4bbl but that needs a rebuild as well, and it looks like it was dropped because the linkages are angled funny. Both carbs were purchases off e-bay.
MAX 10 IMAGES -> Continued
Epoxy Spacer, aluminum spacer tubes are embedded inside the epoxy, then I used longer bolts to hold it all together.
4bbl Manifold
Last edited by A20A1; 06-14-2012 at 09:13 AM.
- llia
Theres a whole lot of "WTF mods!" lol
I have an old Nikki RX7 4-bbl I got off ebay for a penny, I've been itching to do that with it, I just don't know if the jetting would be good as is because tuning jets are expensive/hard to find for these. It's a small 4bbl so I think it would work well. Just gotta get around to it I guess. I think it would look good under the hood of my Rat Rocket
Eric
3geez member since October 12, 2000
"All this worldly wisdom was once the unamiable heresy of some wise man." - Henry David Thoreau
Last edited by niles; 08-31-2012 at 01:38 PM. Reason: fix pictures
Wow... You turned your windshield into a headlight and your hatch window into a taillight. That HAS to of gotten you pulled over at least once, no? lol.
Heres my wtf mods. They might not be completely wtf, but they are at least uncommon.
And a video of my other wtf mod(s).
http://www.youtube.com/watch?v=SRBmN...ature=youtu.be
Last edited by 89HatchbackLxi; 06-23-2012 at 11:36 PM.
I don't drive with the windshield light much, mostly just to show off.
I got safety lights too.
You guys do some seriously wacky shit. Lost, what kind of intake/injection is going on in that sea of a/n fittings?
Low is a Lifestyle, and I'm living the life.
forgot these:
see-thru gauge
i'll bet lost has about 3 of these:
health and safety warning about the suspension:
Eric
3geez member since October 12, 2000
"All this worldly wisdom was once the unamiable heresy of some wise man." - Henry David Thoreau
Here is the How-To on the turn signals: https://www.3geez.com/forum/showthread.php?t=78848
Last edited by niles; 10-02-2012 at 12:19 PM. Reason: Added Link
I'll keep an eye out for another one, I fly to california next month
Eric
3geez member since October 12, 2000
"All this worldly wisdom was once the unamiable heresy of some wise man." - Henry David Thoreau
cup holder
hahahaha i love it
it's sized perfectly for burger king cups
Bookmarks