ordered innovative b series mounts

[beran24]

okay i just have a few questions wondering if anyone could answer for me please. Fist im swapping to efi cuz the car was carb so im pulling everything from the exi and putting it in my dx. I was wondering what needs to be changed to convert my heat controls from the slides to the push bottons?

Second is there any sensors or stuff the plugs into the b18 harness that i should pick up off my buddys integra or will i be able to use all the stuff from my exi with re wiring it to the b18?

I plan on cutting the plugs from the harness in his integra that goto the ecu to make myself a jumper to convert the exi harness to obd1

[guaynabo89]

1st the whole dash/blower assembly etc. (can swap covers) The interior wiring harness.


second the engine should have all the sensors on it you need, therefore just require you to do wiring.

third go ahead. if you have no problems reading pinouts shouldnt be a problem.

[beran24]

1st the whole dash/blower assembly etc. (can swap covers) The interior wiring harness.


second the engine should have all the sensors on it you need, therefore just require you to do wiring.

third go ahead. if you have no problems reading pinouts shouldnt be a problem.

thanks for the help. I dont wanna pay someone for a wireharness cuz the only way to learn myself is do it.

also i have power window assemblys for a 2 door that i wanna use in my door the 4 door harness going to the windows should be the same right

[Vector]

the motor assembly should fit, but the power window motor rail/slider may not bolt up to the glass because the 2rd assemblys were longer than the 4dr due to side of glass. similar issue with my 88 hatch.

providing the motors are from another accord 86-89, the electrical should be plugin play for power windows.

[beran24]

the motor assembly should fit, but the power window motor rail/slider may not bolt up to the glass because the 2rd assemblys were longer than the 4dr due to side of glass. similar issue with my 88 hatch.

providing the motors are from another accord 86-89, the electrical should be plugin play for power windows.

I have the complete slides from a 2 door that had power windows so it shouldn't be a problem.

[markmdz89hatch]

subscribed...

[beran24]

goal tomorrow provided it dont rain or snow is get the heater unit out of it and hopefully the wiring

[Tomisimo]

Dont forget to take lots of pics, and post then.. this makes threads interesting..

Nice to see you getting it moving. I'll be watching this thread.

[Vector]

I have the complete slides from a 2 door that had power windows so it shouldn't be a problem.

ok... #1 i really need to learn how to read, and write aparently... i dont even remember replying that... i must have been high @ the time or somthing.. lol

#2 i probably thought at the time you were going to use pw from a 4dr...into a 2dr or vis-versa... either way, ignore my idiocy...

the wiring itself should still plug into the motors from the front doors of the harness..

[beran24]

ok... #1 i really need to learn how to read, and write aparently... i dont even remember replying that... i must have been high @ the time or somthing.. lol

#2 i probably thought at the time you were going to use pw from a 4dr...into a 2dr or vis-versa... either way, ignore my idiocy...

the wiring itself should still plug into the motors from the front doors of the harness..

haha dont worry about it, cant do anything today its raining like a bitch outside

[guaynabo89]

Whats the word on the mounts and engine/tranny?

[mkymonkey]

Whats the word on the mounts and engine/tranny?

x7

[RobT5580]

I have not heard anything other than that last email that both of us recieved.

[markmdz89hatch]

no worries guys. I might have gotten some info that they should ship next week at the latest. Please don't ask where the info is coming from, but it is a reputable source.

Please keep this thread up with all updates as I'm dying to actually see this done.

[beran24]

no worries guys. I might have gotten some info that they should ship next week at the latest. Please don't ask where the info is coming from, but it is a reputable source.

Please keep this thread up with all updates as I'm dying to actually see this done.

I been email spark tech they told of over a week ago that they would be sent out in a week and they still haven given me shipment info so i emailed them again all they said is they should be ready real soon.

[markmdz89hatch]

I spoke to someone directly at Innovative. This person has direct knowledge of the orders and their progress. He mentioned that they should/would ship next week.

[beran24]

I spoke to someone directly at Innovative. This person has direct knowledge of the orders and their progress. He mentioned that they should/would ship next week.

Well hopefully this happens cuz i can't wait to get them rob should have his first tho if both of are's ship out the same day because mine have to come way up to canada.

[beran24]

still no new info on the mounts so i email sparktec again saying "hey its been almost a month since i put in my order for these mounts u guys keep saying they will be shipped out soon so i just really want to know whats going on with them" so ill let you guys know if they tell me anything new.

[JohnBoy]

it might take a little bit. i had to wait 2 month to get a sub frame for my cr500. it takes a bit to get the jig set up. but when i got it it was b e a u ti ful

[beran24]

today i removed the rad, and un pluged the old wire harness and got it all pulled out through the inner fender.

[beran24]

just wondering if someone could tell me how the heater assembly is held in lol i been looking at it tryin to figure it out. is there a bolt on it that goes through the firewall or something? its made in 3 sections, i got the piece on the passenger side out, then there is the heater core i got that un hooked, but im talking about the piece that sets like right in the middle of the car. any tips thanks guys.

[2ndGenGuy]

Yep there's a bolt that goes through the firewall.

[beran24]

Yep there's a bolt that goes through the firewall.

thanks i seen a bolt from the engine bay i figured that must be it. im gonna wait til i lift the eninge out lol it will make it alot easyer gettin in there

[beran24]

so i guess i had a phone call today and i wasnt home to take it but i think it was to re asure me that i will be getting my mounts at some point because the emailed me back saying: Brandon, we are not lying to you, it is in production by Innovative, I don't have a turnaround time by them but believe us it is in order and as soon as we get more word from them, we will let you know

[beran24]

got reallly good news just got home checked my email the mounts have been finished and shipped out expected delivery date is march 22. cant wait so for work on the car didnt get much more done i been busy, just took the axles out today thats about it.